Mazda Navajo Alternators and Starters

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
• Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

Product Features:

• Designed to OE standards for ease of installation
• Contain more pure copper windings than found on most vehicles and create a stronger magnetic field in even the hottest environments for better performance.
• Solenoids contain cadmium-plated copper discs and solid contact bolts reduce voltage drop to deliver full battery power to the starter and have pure copper battery terminal studs that reduce resistance and permit higher current flow.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

The Bosch Premium Alternator is engineered for peak performance and unmatched reliability, making it a top choice for demanding driving conditions. Featuring 100% new components, it is built to endure the harshest environments, excessive heat, and high electrical demands, ensuring a long service life. With an amperage rating of 95A and a 12 VDC output, this alternator delivers consistent power to meet your vehicle’s needs. Its aluminum construction enhances durability, while all mounting points are precisely gauged, resized, or rethreaded for a perfect fit during installation. Designed for clockwise rotation, it seamlessly integrates into your vehicle’s system. As an added benefit, every purchase includes free 24-hour Roadside Assistance Protection, providing extra peace of mind. Choose Bosch for a reliable, high-performance alternator that keeps your vehicle running smoothly.

Product Features:

Product Features:
• 100% new components withstand the harshest environments for the best performance and longest life
• Built specifically to withstand excessive heat and high electrical demands.
• All mounting points 100% gauged and resized or rethreaded for proper fit
• Free 24-hour Roadside Assistance Protection with purchase of any Bosch Alternator
• The aluminum construction enhances durability while maintaining a lightweight design, ensuring optimal performance and longevity in demanding driving conditions.

Carquest Standard alternators are designed and built to meet original equipment (O.E.) specifications, while providing great value. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. All of our Carquest Standard alternators are inspected and 100% tested to ensure they are built to meet OEM fit, form and function. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Professional alternators are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new alternators are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional alternators are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new alternators are built with all new components and are 100% triple tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• All new components are utilized to ensure long service life
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672
• Rotors and stators are load tested and double insulated for maximum charging performance

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Starters with 100% NEW construction will restore hard working vehicles to exceed OE specified performance & endurance. All new units and components offer unmatched performance, reduce downtime & customer comebacks. Carquest HD alternators are pri

Product Features:

• High quality components form the foundation our parts are built from. Transpo’s innovative and high quality electronic technologies for internal components are incorporated to achieve high performance outputs.
• Power & Efficiency are designed into every component. No matter the ambient temperature, starters will provide maximum cranking power to get engines running.
• Connectors and power transmission components are highly resistant to extreme moisture environments because we use nickel plated contactors and double armature coating. We maintain a rigorous test schedule with endurance, salt spray, dirt and grime and out
• Integrated magnetic switch provides protection against weak power from batteries.
• Over-Crank Protection (OCP) Monitors heat in starter from over cranking & shuts down starter to prevent burning
• Precision design and machining are the Extreme vibration failure solution. Vehicles often perform in adverse conditions like extreme temperatures that create tolerance shifts that produce high frequency vibration, which leads to resistance in power transf
• Load dump protection ensures transient voltage spikes do not damage transistor
• Improved power transmission with lower engine speed keeps accessories and powered implements running at maximum output without additional load to the engine.

Carquest Starters with 100% NEW construction will restore hard working vehicles to exceed OE specified performance & endurance. All new units and components offer unmatched performance, reduce downtime & customer comebacks. Carquest HD alternators are pri

Product Features:

• High quality components form the foundation our parts are built from. Transpo’s innovative and high quality electronic technologies for internal components are incorporated to achieve high performance outputs.
• Power & Efficiency are designed into every component. No matter the ambient temperature, starters will provide maximum cranking power to get engines running.
• Connectors and power transmission components are highly resistant to extreme moisture environments because we use nickel plated contactors and double armature coating. We maintain a rigorous test schedule with endurance, salt spray, dirt and grime and out
• Integrated magnetic switch provides protection against weak power from batteries.
• Over-Crank Protection (OCP) Monitors heat in starter from over cranking & shuts down starter to prevent burning
• Precision design and machining are the Extreme vibration failure solution. Vehicles often perform in adverse conditions like extreme temperatures that create tolerance shifts that produce high frequency vibration, which leads to resistance in power transf
• Load dump protection ensures transient voltage spikes do not damage transistor
• Improved power transmission with lower engine speed keeps accessories and powered implements running at maximum output without additional load to the engine.

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
• Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
• 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Standard starters are designed and built to meet original equipment (O.E.) specifications, while providing great value. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. All of our Carquest Standard starters are inspected and 100% tested to ensure they are built to meet OEM fit, form and function. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Remanufactured (not rebuilt) to meet or exceed OEM quality in fit, form, and function
• Triple Testing process (component, assembly process and final product) to ensure reliability
• An economical option that meets or exceeds OE specifications
• Tech Hotline with trained ASE Certified Technicians: Call CARQUEST Technical Support at 1-800-228-9672
• One year warranty gives you peace of mind
• Designed to meet OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Standard starters are designed and built to meet original equipment (O.E.) specifications, while providing great value. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. All of our Carquest Standard starters are inspected and 100% tested to ensure they are built to meet OEM fit, form and function. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Built to meet OE quality in fit, form, and function.
• Units are rebuilt with critical parts and components that are 100% new.
• Designed to meet OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Designed to meet OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by a Limited Warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Each unit is triple-tested to ensure quality and performance
• All wear components (brushes, bushings, and bearings) are replaced with all NEW components in the remanufacturing process
• Tech Hotline with trained ASE Certified Technicians: Call Carquest Technical Support at 1-800-228-9672
• Remanufactured by an IATF/TS 16949 certified supplier to meet the highest industry standards for quality and reliability.
• Designed to meet or exceed original equipment (OE) specifications for fit, form, and function, ensuring seamless compatibility and dependable performance.

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability.

Product Features:

• Premium 100% New Starter
• Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
• Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
• Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672
• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

The Carquest Premium Starter is meticulously remanufactured to deliver exceptional reliability and performance, meeting or exceeding original equipment manufacturer (OEM) standards. Designed for Ford vehicles, this starter operates at 12.0 VDC with a precise 10-tooth configuration, ensuring optimal compatibility and fit. Each unit undergoes a rigorous triple-testing process, from individual components to final assembly, guaranteeing dependable service. Unlike rebuilt alternatives, this remanufactured starter features all-new wear components, including brushes, bushings, and bearings, for enhanced durability and longevity. With a focus on quality and functionality, it provides a seamless replacement that restores your vehicle’s starting system to peak performance. For added support, Carquest offers access to ASE Certified Technicians via their Tech Hotline, ensuring expert guidance when needed. Choose this premium starter for a reliable, high-quality solution tailored to your Ford vehicle.

Product Features:

Product Features:
• Each unit is triple-tested to ensure quality and performance
• All wear components (brushes, bushings, and bearings) are replaced with all NEW components in the remanufacturing process
• Tech Hotline with trained ASE Certified Technicians: Call Carquest Technical Support at 1-800-228-9672
• Designed specifically for Ford vehicles, ensuring precise fit and compatibility.
• Remanufactured to meet or exceed OEM standards, delivering reliable and consistent performance.

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability.

Product Features:

• Built for extremes! Our new and reman starters and alternators are 100% factory tested to ensure reliable performance, under extremes of heat, cold and high demand
• Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
• Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
• Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life