from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$246.99

Yukon forged yoke for Ford 8.8″ with a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$404.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Carbon fiber clutches

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$10.49

Product Features:

SOLID SPACER FORD 8.8″ & 9″

from

$299.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline Trac Loc positraction
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$8.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$37.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$286.99

Yukon flange yoke for 8.8″ Ford passenger and 8.8″ Ford IFS truck (4.3″ OD). All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
Round companion flange
4.3″ O.D.

from

$30.99

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Ford 7.5″, 8.8″, 9″ and 10.25″

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$179.99

Product Features:

FRD 10BLT 8.8 R/P 4.56A MG

from

$16.99

Standard open cross pin shaft (.750″) for Ford 8″, 8.8″, 9″ and Model 20.

Product Features:

Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
Fits standard open differentials only
0.750″ diameter

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$67.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

Trac Loc spring
Fits Ford 7.5″

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$15.99

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$64.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$194.99

Mini Spool for Ford 8.8″ with 31 spline axles and 7/8″ cross pin. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″ with 31 spline axles
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$20.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$13.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.99

Product Features:

Brand may vary by location

from

$22.49

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience