Land Rover Discovery Sport Cooling and Climate Controls

Product Features:

• Designed, tested, and built by application
• OE performance, fit, and appearance
• Precision machined
• Out of box installation

The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:

• All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
• The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
• The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
• The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
• On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
• After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.

Carquest Expansion Valves are designed to regulate the flow of refrigerant through the air conditioning system to provide optimal cooling to the passenger compartment. Each expansion valve is manufactured to original equipment specifications to perform its function even in the harshest climates. Each part is supplied with the necessary gaskets and o-rings for installation.

Product Features:

• The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
• Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
• Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
• O-Rings necessary for installation are included.

A/C Evaporator

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

• Ideal for rigid cast aluminum parts
• Meets OEM Specifications
• Sensor safe & non-corrosive
• Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
• Blowout resistant, allowing leakproof gaskets to be made in just one minute
• Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
• Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
• Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
• Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

Manufactured to meet all OEM specifications. Designed to be easy to install and remove. Manufactured from high quality components with proper relief and vacuum valves. Quality tested to stand up to even the most demanding automotive cooling systems.

Product Features:

• Maintains proper cooling system pressure
• Easy installation and removal
• 100% tested to ensure proper pressure and longevity
• Meets all OEM specifications

Carquest Accumulators and Receiver Driers are designed to store, filter and dry the air conditioning refrigerant to provide proper performance and durability for the air conditioning system. They are manufactured to meet or exceed original equipment specifications.

Product Features:

• All parts meet or exceed original equipment standards for moisture absorption, pressure and temperature resistance, air tightness, vibration resistance, corrosiveness, and pulse pressure.
• Desiccant is 100% tested and assembled in a controlled environment to ensure performance meets or exceeds original equipment standards.
• All accumulators and receiver driers are helium leak tested prior to packaging.
• O-Rings necessary for installation are included.

Carquest Premium offers a complete line of automotive heater cores covering 94% of all North American vehicle applications. Carquest Premium provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability. Carquest Premium offers certified heater cores that meet or exceed OE specifications and are all fitment checked in the actual vehicle’s HVAC heater module and are, thus, ready to be installed right out of the box for a “Drop-In Fit”. Carquest Premium heater cores are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.

Product Features:

• All heater cores are designed and tested to match or exceed OE specifications for form, fit and performance with a clear focus on obtaining the highest heat transfer performance possible through use of quality materials and manufacturing processes to ensu
• Carquest Premium heater cores are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.
• Provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability.
• Carquest Premium offers a complete line of automotive heater cores covering 94% of all North American vehicle applications.
• Our advanced engineering methods coupled with our innovative manufacturing technology provides products to the aftermarket that meet or exceed form, fit, and function of OEM Parts

Rein Automotive OE temperature sensors are made to factory specifications ensuring proper fit, form and function. The temperature sensor is used to report exhaust temperatures to the vehicle’s ECU. The vehicle uses this information to control engine and emission paramaters. Rein temperature sensors include a vehicle specific connector that fits directly into the factory plug.

Product Features:

• Direct OE replacement
• Designed to meet or exceed factory specifications
• Made using high quality materials
• Uses vehicle specific style connector for quick replacement.

New Platinum Pro Radiator

Product Features:

• Made Of Plastic and Aluminum
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

• Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
• Sensor-safe, non-corrosive, RTV silicone
• Protects against leaks caused by vibration and thermal expansion
• Meets performance specs of OE silicone gaskets
• Quickly returns vehicle to service in just 1 minute

High quality OE replacement part with all components needed to complete the job

Product Features:

• Endurance tested the equivalent of 50k miles
• Includes specific electrical connector to eliminate splicing
• Charged with lubricant to reduce internal friction promoting enhanced system performance and longevity
• For ease of installation this compressor includes a direct fit OE style connector as well as all gaskets, O-rings, or seals needed to repair your car
• Each unit is individually leak, vacuum and pressure tested prior to packaging to ensure leak free performance

Starter Relay

This replacement engine coolant thermostat housing assembly is engineered to match the fit and durability of the stock housing assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

• Ideal replacement – this engine coolant thermostat housing assembly directly replaces the original water outlet on specified vehicle years, makes and models
• Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
• Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
• Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housing assemblies

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

• High grade stainless steel and copper construction
• Meets or exceeds OEM standards
• Consistent and precise response to cooling system needs
• Original equipment design for worry-free direct fit replacement
• 100% tested and calibrated

Carquest premium direct replacement resistors are designed to match the operation and performance of the original equipment to restore the proper heating and cooling functionality.

Product Features:

• Restores Functionality- Manufactured to original equipment specifications to restore full HVAC operation
• Original equipment quality – Carquest blower motor resistors meet the high quality material standards and tolerances as the original equipment
• Complete kit – Each kit includes the resistor, connector, and splice connectors to complete the job
• Direct replacement – Carquest blower motor resistor kits are a direct replacement to the original equipment resistor

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

The ACM A/C Condenser is manufactured to exact OEM specifications for quality fit and performance.

Product Features:

• OE-Equivalent and Direct fit Application.
• Meet or exceed OEM specifications.
• Utilizes the factory style mounts, connectors and fittings.
• Compatible with R12 and R134a refrigerant.
• Applicable gaskets and O-rings supplied with each part.

New Platinum Pro A/C Condenser, 07 S80 From Chassis 3119, Various Others

Product Features:

• 07 S80 From Chassis 3119, Various Others, Made Of Aluminum
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

• High torque and rigidity
• Sensor-safe, non-corrosive formula
• OEM specified
• Low-odor, non-corrosive formula
• Ideal for closed spaced bolt patterns

High quality OE replacement part with all components needed to complete the job

Product Features:

• Endurance tested the equivalent of 50k miles
• Includes specific electrical connector to eliminate splicing
• Charged with lubricant to reduce internal friction promoting enhanced system performance and longevity
• For ease of installation this compressor includes a direct fit OE style connector as well as all gaskets, O-rings, or seals needed to repair your car
• Each unit is individually leak, vacuum and pressure tested prior to packaging to ensure leak free performance