from

$35.99

New Standard Replacement A/C Receiver Drier

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$79.99

ACDelco GM Original Equipment HVAC Air Inlet Door Actuators are electric motors attached to the HVAC housing that open or close the air inlet door, allowing the driver to select fresh air or recirculate modes. They are GM-recommended replacements for your vehicle’s original components. These original equipment air inlet door actuators have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

Restore air inlet door operation caused by worn actuator
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$56.99

The Carquest Premium line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
All units are tested using automated end-of-line testing equipment that pressurizes the sensor and checks full-spectrum functionality and electrical output to ensure each part meets manufacturing specifications before packaging.

from

$33.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$146.99

The Carquest condenser is an integral component of the motor vehicle air conditioning system. This part condenses the refrigerant into a liquid to prepare it for entry into the compressor. The condenser is manufactured according to OEM design specifications to ensure a long life with quality performance. Exact design standards produce a seamless fit into the engine compartment.

Product Features:

This is a parallel flow condenser that contains small micro-channels. It is highly recommended that this condenser be replaced if a failure has occurred in the vehicle’s air conditioning system that has resulted in debris contaminating the system.
The Carquest condenser production process includes quality driven details such as using zinc-coated tubes and electrostatic paint spray at high temperatures to provide the best corrosion resistance and durability in our condensers.
Continuous molds, laser welding machines, semi-automatic assembly stations and other advanced equipment provide quality products.
Each condenser uses only the highest quality raw materials including pure aluminum (not substandard or recycled) to provide the highest quality standards from beginning to finished product.
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak.
Our condensers are manufactured from rigid design standards to fit OEM dimensions.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.
Each Carquest condenser is packaged using superior box construction. This box is easy to open and seal. Each condenser is packaged in the box with internal protection to keep the part centered and away from the package edges.

from

$362.99

Carquest New Compressors are designed, manufactured and tested to meet or exceed strict original equipment specifications for superior quality and performance. Each new compressor is tested to provide durable life to the vehicle’s air conditioning system. All new compressor components are assembled using state of the art equipment and techniques to ensure smooth operation. Each part is equipped with a clutch and connector that matches the original equipment part and provides an exact replacement to your vehicle’s part. All compressors are supplied with the necessary gaskets and o-rings for installation.

Product Features:

Each new compressor design undergoes rigorous life cycle testing at high RPMs and pressures to ensure that they can withstand years in the harshest conditions.
New compressors are designed with utmost precision using 3D coordinate measuring machines to ensure a perfect fit.
The production process contains automated controls at every stage that alerts and halts production in case of an error, assuring that the finished product will always be flawless.
All new compressors must pass a helium leak test and pump up function test prior to packaging.
O-Rings and gaskets necessary for installation are included.

from

$97.99

Advance Auto Parts is proud to carry comparable exact-fit parts from multiple vendors, as such, the item you receive may be one of two quality brands. Both brands meet the same fitment requirements and are equal in their performance and specifications. The fan clutch is the component of the cooling system that varies the fan speed to meet the cooling needs of the engine. The fan clutch provides high airflow volume and, by only operating the fan as needed, promotes good fuel economy. Carquest fan clutches are designed to meet OE performance specifications.

Product Features:

Designed, tested, and built by application
OE performance, fit, and appearance
Precision machined
Out of box installation
Designed, tested, and built by application
OE performance, fit, and appearance
Precision machined
Out of box installation

from

$127.99

Carquest Premium heater cores use advanced engineering methods together with innovative manufacturing technology resulting in a product that meets or exceeds form, fit, and function.

Product Features:

Designed to keep your A/C system in top shape and built to provide long-lasting service.
Our advanced engineering methods coupled with our innovative manufacturing technology provide products to the aftermarket that meet or exceed form, fit, and function of OEM parts.
Our advanced engineering methods coupled with our innovative manufacturing technology provide products to the aftermarket that meet or exceed form, fit, and function of OEM parts.

from

$94.99

Carquest Evaporators are designed to remove heat from the air inside the passenger compartment of a vehicle resulting in cooler air temperatures. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

from

$133.99

An ACDelco Professional, premium aftermarket Engine Water Pump circulates coolant through your vehicle’s radiator and engine system to help maintain proper engine temperature and performance. The gaskets, seals, and O-rings packaged with this Professional, premium aftermarket water pump help guarantee that all necessary parts are available for trouble-free installation. ACDelco Professional Water Pumps are a high quality replacement for many vehicles on the road today. This premium aftermarket replacement engine water pump is manufactured to meet your expectations for fit, form, and function.

Product Features:

All Makes water pumps fit GM vehicles as well as a wide range of non-GM vehicles
Thoroughly tested for reliable, leak-free performance
Coated seals support seal longevity and durability
Heat-treated shaft assemblies provide superior strength and durability over non-treated assemblies
High-quality bearings are permanently sealed and lubricated for greater durability and long life
Come with premium, high-quality replacement components needed for trouble-free and accurate installation
Uniform wall sections and smooth coolant-flow cavities for efficient operation
Cast-iron or aluminum design, depending on vehicle application

from

$69.99

ACDelco GM Original Equipment Multi Purpose Sensor is a GM-recommended replacement component for one or more of the following vehicle systems: hvac. This original equipment sensor will provide the same performance, durability, and service life you expect from General Motors.

Product Features:

GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$108.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Rapid-Cool Thin-Line electric fans
12″ Diameter
800 CFM
Use as a pusher or puller fan
Motors built and tested to quality specifications
12 in. universal fit reversible fan
800 CFM
UNIVERSAL fan, NOT a direct OE replacement. Measure core and verify space.

from

$71.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to ensure proper air/fuel ratio along with proper operation of the cooling fans and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include, check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clips included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$112.99

ACDelco GM Original Equipment Engine Coolant Thermostat Housing Assemblies are designed, engineered, and tested to rigorous standards, and are backed by General Motors. ACDelco GM Original Equipment parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some ACDelco GM Original Equipment parts may have formerly appeared as GM Genuine Parts (OE) or ACDelco Professional.

Product Features:

Some ACDelco GM Original Equipment parts may have formerly appeared as GM Genuine Parts (OE) or ACDelco Professional
ACDelco GM Original Equipment parts are designed, engineered and tested to rigorous standards, and are backed by General Motors.
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$8.99

GM Genuine Parts Wiring Relays are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These relays help connect or disconnect power to a vehicle accessory when it receives a low voltage signal from a switch. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Helps connect or disconnect power to vehicle accessories
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$95.99

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

Machined metal construction
Works with MT-300 pressure tester
Tests coolant caps
Professional quality

from

$21.79

GM Genuine Parts Rubber-Bonded Sealing Washers are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
GM regularly updates production and service part designs to integrate new materials and technologies

from

$18.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$35.99

ACDelco GM Original Equipment Wiring Relays are designed, engineered, and tested to rigorous standards, and are backed by General Motors. ACDelco GM Original Equipment parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some ACDelco GM Original Equipment parts may have formerly appeared as GM Genuine Parts (OE) or ACDelco Professional.

Product Features:

Some ACDelco GM Original Equipment parts may have formerly appeared as GM Genuine Parts (OE) or ACDelco Professional
ACDelco GM Original Equipment parts are designed, engineered and tested to rigorous standards, and are backed by General Motors.
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$41.99

ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

Protective outer coverings help provide long-lasting durability
Color-coded wires allow for easy installation
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$62.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$7.99

MAHLE® gaskets provide world class sealing products trusted by OEMs & Technicians around the globe.

Product Features:

All MAHLE gaskets meet or exceed the original equipment specifications providing the finest sealing products available
MAHLE gaskets utilizes OE equivalent or better materials in all our gaskets
MAHLE gaskets is the leader in Domestic, Asian and European applications
The contents of MAHLE gaskets are packaged in shrink wrapped tray, giving you the added security of knowing that you have the right parts, prior to opening the package

from

$125.99

ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

Protective outer coverings help provide long-lasting durability
Color-coded wires allow for easy installation
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$43.99

WIRE CONNECTOR

from

$22.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.