International SA120 Belts and Hoses
Top International SA120 Belts and Hoses Categories
We carry over 19 Belts and Hoses in inventory for the International SA120. If you’re looking for aftermarket Belts and Hoses for your International SA120, check out all these categories:
Essential International SA120 Belts and Hoses
Gates – Molded Coolant Hose (Part No.20206)
from
$26.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation – the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
- Temperature Rating: -40° F to 275° F (-40° C to 135° C) in coolant hose applications.
- Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates – Premium Molded Coolant Hose (Part No.20357)
from
$25.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Molded Heater Hose: EPDM, Steel, Direct Fit, 2" Inside Diameter (Part No.26508)
from
$37.99
Product Features:
See More
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Dayco – Double Cog V-Belt; 43.5 Inch Long, Exact Fit Premium Quality (Part No.24435)
from
$13.99
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and pro
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Driveworks – Automotive V-Belt, Driveworks (Part No.30517)
from
$4.49
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Gates – Green Stripe« Truck & Bus Series V-Belt (Part No.TR28445)
from
$38.99
Specifically designed for heavy-duty truck, bus and off-road equipment applications. Absorbs normal shock loads without damage to the belt.
Product Features:
See More
Product Features:
- Molded notches reduce bending stress, especially on small diameter pulleys, while dissipating heat
- High modulus, high strength tensile cord
- Oil and heat-resistant construction throughout
- Meets SAE J636b and SAE J637 specifications
- Meets RMA oil and heat resistant standards and static conductivity requirements
- NOTE: Some sizes available as Gates PowerBand joined V-belts
Gates – Automotive XL« High Capacity V-Belt (Part No.9440)
from
$23.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL« High Capacity V-Belt (Part No.9341)
from
$28.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Premium Molded Coolant Hose (Part No.20338)
from
$9.79
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Gates – Molded Heater Hose: EPDM, Steel, Direct Fit, 2" Inside Diameter (Part No.26509)
from
$37.99
Product Features:
See More
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
International SA120 Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your International SA120
You love your SA120. So we’ve made it easier than ever to help you find International SA120 Belts and Hoses in our online catalog. Our inventory holds 19 aftermarket and OEM Belts and Hoses for your International SA120, ranging from $4.29 to $79.99.
We offer parts from 4 brands trusted to make quality Belts and Hoses for your International SA120. Before you buy, take some time to read through customer reviews. We currently have 4 reviews of International SA120 Belts and Hoses from previous customers. Some of the top rated parts include Automotive V-Belt, Driveworks with 5.0 stars.
Find your SA120 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your International SA120 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your International SA120
Our inventory holds Belts and Hoses for your International SA120 from 4 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Imperial, and Gates, all of which can keep that International happy.
We have Dayco parts available for your International SA120 in categories like Serpentine and V Belts. Some of the top-rated Dayco parts in these categories are:
FAQs for International SA120 Belts and Hoses
What are the most purchased Belts and Hoses for the International SA120?
Out of 19 Belts and Hoses for the International SA120, the most popular in our inventory are:
from
$21.29
This product is not rated
Bottom Cog V-Belt; 46.25 Inch Long, Exact Fit Premium Quality
V-Belts
What are the top-rated International SA120 Belts and Hoses?
Top-rated Belts and Hoses for your International SA120 based on customer reviews/ratings are:
