International 4400LP Drivetrains

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

• The cross is hot forged for the higher torque and horsepower
• The bearing cups are made by cold forging, having higher strength and better rigidity
• Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
• Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
• Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
• Snap rings are held to strict tolerances to ensure proper cup position and retention
• Nitrile rubber seals to optimize grease retention and reduce contamination

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1955-2018
• Weight approx: 4 Lbs
• BEARING ID / BORE: 1.5750 In. / 40 mm
• CENTERLINE: 2.48 In. / 63 mm
• Mount Width: 6.62 In. / 168 mm
• Style: Round Frame
• Not Pictured: Two Dust Shields

Anchor 6035 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1955-2002
• Weight approx: 2 Lbs
• BEARING ID / BORE: 1.1811 In. / 30 mm
• CENTERLINE: 3.50 In. / 89 mm
• Mount Width: 1.50 In. / 38 mm
• Complete Mount

Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1955-2018
• Weight approx: 3 Lbs
• BEARING ID / BORE: 1.3780 In. / 35 mm
• CENTERLINE: 2.28 In. / 58 mm
• Mount Width: 6.62 In. / 168 mm
• Style: Round Frame
• Complete Mount

Anchor 6040 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1957-2018
• Weight approx: 4 Lbs
• BEARING ID / BORE: 1.7680 In. / 45 mm
• CENTERLINE: 2.75 In. / 70 mm
• Mount Width: 7.62 In. / 194 mm

Anchor 6048 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1957-2013
• Weight approx: 6 Lbs
• BEARING ID / BORE: 1.9685 In. / 50 mm
• CENTERLINE: 2.80 In. / 71 mm
• Mount Width: 7.62 In. / 194 mm

Anchor 6049 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1957-2018
• Weight approx: 8 Lbs
• BEARING ID / BORE: 2.3622 In. / 60 mm
• CENTERLINE: 3.37 In. / 86 mm
• Mount Width: 8.62 In. / 219 mm