International 1200D Belts and Hoses
Top International 1200D Belts and Hoses Categories
We carry over 40 Belts and Hoses in inventory for the International 1200D. If you’re looking for aftermarket Belts and Hoses for your International 1200D, check out all these categories:
Essential International 1200D Belts and Hoses
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Gates – Premium Molded Coolant Hose (Part No.20847)
from
$66.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13" Long, 2.25" Diameter (Part No.C70416)
from
$17.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Flex Radiator Hoses; EPDM Rubber, 19.88 Inch Long, 1.5 Inch Inner Dia. (Part No.81181)
from
$21.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia. (Part No.81341)
from
$18.79
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5" Long, 1.75" Diameter (Part No.A70924)
from
$15.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 3.25" Long, .63" Diameter (Part No.A70001)
from
$10.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.20357)
from
$25.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; Neoprene, Heavy Duty, 14 Inch Long, 2.25 Inch Inner Dia. (Part No.82181GL)
from
$32.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent splitting, ballooning and elongation as well as resist ozone and other detrimental environmental elements, coolants and temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). With corrugations that provide excellent hose flexibility without flattening or collapsing, the Dayco flex radiator hose also features a helical steel coil spring for increased flexibility.
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
Gates – Premium Molded Coolant Hose (Part No.20639)
from
$82.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25478)
from
$16.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Green Stripe« Heavy-Duty Vulco-Flex« Coolant Hose (Part No.26611)
from
$34.99
Heavy-duty flexible hose designed to replace straight or curved coolant hoses. The benefit is maximum coverage with minimum inventory. Hose inside diameter remains constant from end to end. No convolutions inside hose so tube is smooth, allowing free coolant flow. Approved for marine applications.
Product Features:
See More
Product Features:
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9510HD)
from
$44.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Driveworks – Automotive V-Belt (Part No.43513)
from
$5.29
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Driveworks – Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count (Part No.44515)
from
$5.49
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.
Product Features:
See More
Product Features:
- Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
- No-Noise Advanced Design EPDM rubber compound for quiet extended life
Driveworks – Automotive V-Belt (Part No.33017)
from
$5.29
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 60 Inch Long, Exact Fit Premium Quality (Part No.15600)
from
$21.99
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Gates – Automotive XL« High Capacity V-Belt (Part No.9440)
from
$23.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL« High Capacity V-Belt (Part No.9425)
from
$29.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL« High Capacity V-Belt (Part No.9341)
from
$28.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Driveworks – Automotive V-Belt, Driveworks (Part No.42517)
from
$2.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 61 Inch Long, Exact Fit Premium Quality (Part No.15610)
from
$21.99
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Gates – Automotive XL« High Capacity V-Belt (Part No.9330)
from
$31.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Dayco – Bottom Cog V-Belt; 42.5 Inch Long, Exact Fit Premium Quality (Part No.17425)
from
$15.49
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
International 1200D Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your International 1200D
You love your 1200D. So we’ve made it easier than ever to help you find International 1200D Belts and Hoses in our online catalog. Our inventory holds 40 aftermarket and OEM Belts and Hoses for your International 1200D, ranging from $2.99 to $82.99.
We offer parts from 4 brands trusted to make quality Belts and Hoses for your International 1200D. Before you buy, take some time to read through customer reviews. We currently have 468 reviews of International 1200D Belts and Hoses from previous customers. Some of the top rated parts include Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count with 4.3 stars and Automotive V-Belt, Driveworks with 5.0 stars.
Find your 1200D Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your International 1200D part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your International 1200D
Our inventory holds Belts and Hoses for your International 1200D from 4 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Imperial, and Gates, all of which can keep that International happy.
We have Dayco parts available for your International 1200D in categories like Serpentine and V Belts. Some of the top-rated Dayco parts in these categories are:
from
$10.99
(7)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 3.25" Long, .63" Diameter
By-Pass Hoses
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your International 1200D across several catalog categories, including Serpentine and V Belts and Radiator Hoses. Some of our most reviewed Dayco parts include:
from
$18.79
(3)
Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia.
Coolant Hoses
from
$21.99
(2)
Flex Radiator Hoses; EPDM Rubber, 19.88 Inch Long, 1.5 Inch Inner Dia.
Lower Radiator Hoses
FAQs for International 1200D Belts and Hoses
What are the most purchased Belts and Hoses for the International 1200D?
Out of 40 Belts and Hoses for the International 1200D, the most popular in our inventory are:
from
$16.29
This product is not rated
Bottom Cog V-Belt; 37.5 Inch Long, Exact Fit Premium Quality
V-Belts
from
$15.79
This product is not rated
Bottom Cog V-Belt; 53 Inch Long, Exact Fit Premium Quality
V-Belts
What are the top-rated International 1200D Belts and Hoses?
Top-rated Belts and Hoses for your International 1200D based on customer reviews/ratings are:
from
$5.49
(12)
Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count
“Appears to be a great fit and above average quality.”
