Honda Passport Belts and Hoses

Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• Meets Type EC electro-chemical requirements as specified in SAE J1684

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:

• Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
• Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
• Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
• Resists oil, heat, ozone, weather and aging for improved belt life
• Meets or exceeds SAE J636C specifications

Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:

• Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
• Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
• Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
• Resists oil, heat, ozone, weather and aging for improved belt life
• Meets or exceeds SAE J636C specifications

Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:

• Engine oil cooler hose
• Size: 1/2″ x 12′
• Designed for engine oil applications
• 12′ hose length accommodates most applications

Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:

• Metal line kit
• For use in engine oil cooler applications
• Routes oil lines past exhaust manifolds
• Provides protection where standard hoses can fail

Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl

Product Features:

• Designed for the majority of automotive vehicle applications on the road today
• High-quality materials help resist wear and improve belt life
• Features premium lubricated bearings to extend service life
• Meets or exceeds OE quality

This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in Canada to the O.E. specified design and meets all performance and durability requirements. This Heavy duty Steel pulley is 70mm O.D. and comes with an I.D. reduction bearing. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:

• Designed to meet OE specifications
• Not suitable for oil or heat transfer
• Meets SAE J20R4, Class D-2 requirements for improved service hoses
• This hose is designed to prevent splitting, ballooning, and elongation

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.

Product Features:

• OE-Equivalent and a direct fit application.
• Precision bearing
• OE High quality pulley assembly
• Durable long life performance.

Litens was the Original Equipment (O.E.) supplier of this Honda/Acura tensioner and offers this “O..E Exact”* part for the aftermarket. This “O.E. Exact”* part for the aftermarket meets all original equipment form, fit, and function specifications. *(O.E. Exact – Original Equipment manufacturers prohibits the use of their part number or logo on parts sold to other customers. Therefore, the Litens aftermarket part may have minor cosmetic differences but still be exact in performance and design). Choosing The Correct Replacement Part: Both the original equipment and Litens aftermarket tensioner use a round spring versus a flat spring and are marked “Made in Canada”. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

The INA Accessory Belt Tensioner Assembly is a direct fit OEM replacement that contains the same high quality craftsmanship and materials as the original equipment it replaces.

Product Features:

• OE-Equivalent and a direct fit application
• High quality precision spring tension assembly
• OE specified bearing and pulley assembly
• Durable long life performance

This pulley is manufactured by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material and tolerances, specifications and meets performance and durability requirements. The Litens replacement part is constructed of heavy duty steel for long life and trouble free performance Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:

• Manufactured by the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys
• Heavy Duty Steel Pulley
• Precision steel stamping with close tolerance ball bearing pocket.
• Electro-deposited coating (e-coat) for superior corrosion resistance.
• Running surface designed and engineered for proper belt tracking.

Product Features:

• Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
• Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
• OE-quality fit for virtually every domestic or import vehicle on the road today
• Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
• Premium bearings eliminate bearing noise
• Mounting hardware included for some popular applications
• Reliable operation under severe conditions

This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.

Product Features:

• Patented material provides peak performance at prolonged extreme operating temperatures
• Heavy-duty construction resists cracking and wear, even at extreme temperatures
• Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
• Problem solver designed for the toughest applications
• Consistently outperforms other heavy-duty serpentine belts on the market
• Engineered to save your fleet money and reduce downtime
• Tensioner Replacement is Recommended (if equipped)

The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:

• Constructed with heat and ozone resistant EPDM rubber
• Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
• Made with treated polyester cord to reduce belt stretch

The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:

• Constructed with heat and ozone resistant EPDM rubber
• Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
• Made with treated polyester cord to reduce belt stretch