GMC P25 Performance and Racing Products

Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:

• Braided Stainless Steel
• Firewall Mounting
• Includes Oil Fill Tube

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

• Externally mounted coil
• Increases reliability
• Increase performance
• High quality plastic
• Resist spark loss
• Use brass conductors
• Low resistance connections
• No modifications

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.

Product Features:

• HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
• 260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

• ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
• RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
• 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
• CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
• ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
• EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
• ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
• MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.** 

Product Features:

• Proven protection for up to 10,000 miles
• Engineered for use with synthetic or conventional motor oils
• Filter media is a blend of fiber and resin that captures 95% of the dirt particles
• The perfect balance of dirt-trapping efficiency and dirt-holding capacity

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

This Spectre polished aluminum oil pan is designed to fit 1955-’79 small block Chevrolet 283-350 engines with a driver’s side dipstick (except 1962-’67 Chevrolet II and Corvette with stock exhaust). This oil pan is made from a heavy die-cast polished aluminum featuring a finned diamond design. The stock oil capacity is maintained at 4 quarts and uses a 1975 and later gasket with thick front seal. The required mounting fasteners are included.

Product Features:

• Stock 4 quart capacity
• Polished die-cast aluminum
• Finned diamond design finish
• Includes mounting fasteners

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

• Indicates coolant temperature
• Helps prevent coolant injuries
• Fahrenheit and centigrade readings
• Color-coded temperature ranges
• Integrated coolant reclamation valve
• Improves under-hood appearance
• Chromed crown with a colored trim ring

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

• See catalog for application information
• Features 60K V Rated Alkyd Compound

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Product Features:

• Unique Valve Design
• Improves Flow Quantity/Quality
• Supports Engines Up To 550 HP
• Hi-Vol 0.375 in. NPT Inlet/Outlet
• Produces 6 psi
• Gasoline Or Mixed Fuels Only

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.