from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$13.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 58-02; GMC 55-02; INTL 57-02;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2002
Weight approx: 2 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 3.50 INCH / 89 MM
MOUNT WIDTH: 1.50 INCH / 38 MM
COMPLETE MOUNT

from

$4.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$148.99

Yukon 1541H replacement outer stub axle shaft for Dana 44 and 8.5″ GM with a length of 9.94 inches and with 19 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H front axles come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44 in GM truck and Blazer and Jeep Wagoneer with disc brakes
Outer stub
19 spline
9.94″ from end of splines to center of u-joint bore

from

$9.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$57.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$71.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Machined bodies to meet the tight tolerances
Forged and cast material to meet the performance requirement
Minimize the flash lines for less interference
Cleaning process induces compressive strength for increased performance
Machined and threaded holes for mounting ease
Rust preventative added for longer shelf life

from

$129.99

Product Features:

Fits standard rotation Dana Spicer 44
Steel

from

$83.99

Replacement front axle inner seal redi-sleeve for Dana 44 & 8.5″ GM.Yukon Mighty seal.

Product Features:

Axle Redi-sleeve
Fits Dana Spicer 44

from

$9.49

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$155.99

Yukon replacement standard open carrier case for Dana 44, 30 spline, 3.92 & up, bare. This case includes carrier shims, roll pin, ring gear bolts and a cover gasket.

Product Features:

Standard open carrier case
Fits Dana Spicer 44 with 30 spline axles
3.92 and up ratio only
Does not include spider gears
Includes ring gear bolts, carrier shim kit, roll pin and cover gasket

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$12.99

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

Roll pin for Dana Spicer 30 and Dana Spicer 44
0.235″ diameter

from

$7.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$368.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$11.99

Product Features:

CRUSH SLEEVE 14 BOLT 10.5 3116

from

$42.99

Product Features:

Brand may vary by location

from

$16.99

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$14.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$249.99

Product Features:

Installation kit
Includes o-ring for bulkhead fitting, bulkhead fitting, outer fitting, switch, front and rear switch cover, solenoid, zip ties and 20′ air line

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features: