from

$78.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$237.99

Product Features:

GM 10BL 7.5 &7.625 R/P 3.23 MGP 10 3/8 X 18 LH THRED BLTS, PD=1.438

from

$42.99

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. brbrFits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:

Provides Excellent Flange Sealing And Durability
For High-Performance Street, Drag Race & Oval Track Use

from

$1049.99

If you think the torque of that monster diesel is something to brag about then you should feel it with the extra power of NOS. This kit works with stock and modified applications. Vehicles with computer upgrades will benefit even more as nitrous will aid in a clean combustion. Comes complete with 10 pound bottle, bottle brackets, nitrous feed line, large nitrous solenoid, electrical wiring and complete instructions.

Product Features:

Provides Additional Air Your Diesel Wants
Additional 50 HP
w/No Fuel System Or Electronic Upgrades
Complete Kit For Easy Installation

from

$49.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$346.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes

from

$399.99

This is our most popular performance distributor! The housing is machined from a billet of 6061-T6 aluminum on a state-of-the-art CNC machine producing exact tolerances. For high RPM stability, a .500 In. steel shaft is supported by a sealed ball bearing and a long sintered bushing. This shaft also receives a QPQ coating for friction reduction and resistance to corrosion. A precision machined reluctor is attached to the shaft which triggers the magnetic pick-up mounted in the housing. This high output magnetic pick-up is the most accurate way to trigger your ignition. Plus, with no moving parts to wear or adjust, the pick-up is maintenance free! Just above the pick-up is MSD’s adjustable mechanical advance assembly. Different springs and stop bushings are supplied so you can tune an advance curve to match your application.

Product Features:

CNC machined billet aluminum housing and billet aluminum base
Will not accept a vacuum advance canister
Must Be Used w/An MSD Ignition Control
Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
QPQ coated polished steel shaft; guided by sealed ball bearings

from

$199.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$399.99

The X4 Performance Programmer connects high-performance tunes to your vehicle for an immediate boost in horsepower and torque. Awaken your engine to its maximum real potential with preloaded, dyno-proven tune files through the easy-to-use functionality. Instantly increase horsepower and torque and customizeModify a variety of parameters at the touch of a button, all while monitoring gauges on a customizable display.

Product Features:

Read vehicle performance data on a full-color LCD display for easy viewing, day or night.
Preloaded, street-tested, dyno-proven tunes boost horsepower, torque, and throttle sensitivity.
Reads and clears DTC (Diagnostic Trouble Codes) with ease.
Load up to 10 custom tune files created by any SCT Custom Tuning Dealer.
Full color LCD display
High-speed data logging/monitoring
Dual analog inputs
Most popular vehicles supported
Installs quickly and easily
Easy restoration back to stock
User adjustable vehicle parameters
USB Interface cable included
Product might not be available in all states due to local laws.

from

$588.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$16.99

ACCEL Hi-Performance rotors offer superior protection from arc-thru and crossfire. Features hi-performance 60,000 volt alkyd compound, stress-relieved at molding to ensure stability and resist centrifugal forces at high racing RPMs.

Product Features:

Max stability for all RPM ranges
Heavy duty for maximum energy transfer

from

$20.99

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 2.08 inches in diameter. Two per set.

Product Features:

Adds the finishing touch to custom wheels
sold in a pair
Easy Installation
2 Per Set

from

$46.99

Brake Bleeder Screws

from

$16.99

Installs using stock timing cover bolts. Chrome plated steel is a much better compliment to a chromed timing cover. Has markings from 16 degrees before top dead center (BTDC) to 4 degrees after top dead center (ATDC).

Product Features:

Bolts on with existing timing cover bolts
Chrome plated steel is a much better compliment for chrome timing covers
Markings for 16 degrees BTDC to 4 degrees ATDC

from

$258.99

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.

Product Features:

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.
274/286 Advertised Duration, 230/236 Duration @ .050″, .490″/.490″ Lift, 110 Lobe Separation
Valve spring upgrade required
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$29.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

Zinc plated Grade 5 steel
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Ideal For Minimal Space
12-Point Head And Flange
Zinc Plated For Protection

from

$44.99

Original equipment style bracket in high quality chrome for years of service. Includes hardware.

Product Features:

Chrome Plated Heavy Gauge Steel
Can Be Used For Other Applications
Looks Better Than Painted
Hardware included

from

$48.99

Replace your damaged cooling fan blade with this direct replacement. This vehicle-specific application is engineered for a perfect fit and is made from quality materials to ensure durability and restore proper cooling system operation.

Product Features:

Direct replacement – this engine cooling fan blade fits and functions like the original equipment fan blade
Quality construction – manufactured from premium materials for a long service life
Excellent value – original equipment quality at a lower price
Quality tested – has undergone testing to ensure proper fit and performance

from

$14.99

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

4 bolts included in each package
Allen head includes decorative O-ring cap
Triple chrome-plated finish
Fits standard height Chevy Center bolt valve covers

from

$158.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$72.99

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:

Contains all the gaskets needed to change out your camshaft
Fuel Injector O-Ring Not Included
Meets Performance Standards

from

$69.99

HEAVY DUTY-Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. STREET/STRIP-Positive shifts for high performance street use or for competitive events. Hardest, quickest possible shift.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear

from

$34.99

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

Edge Molded Rubber Water Outlet Gasket Is Reusable
Requires No Gasket Sealer
Solid Aluminum Carrier For Strength/rigidity
Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

from

$43.99

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:

Made of Superior Hyper-Flex+ Material
Lasts from 3 to 10 Times Longer
Assemble to Chassis Same Way as OEM
Maintains Factory Ride Characteristics
Simple Way to Increase Vehicle Height

from

$43.99

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features: