from

$170.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$14.29

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$135.99

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

from

$70.99

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

Externally mounted coil
Increases reliability
Increase performance
High quality plastic
Resist spark loss
Use brass conductors
Low resistance connections
No modifications

from

$101.99

Replace your stock black water pump pulley with a chrome plated steel pulley from Mr. Gasket. The pulleys are highly polished then chrome plated for lasting beauty. Designed for big block Chevrolet engines with 5/8 inch water pump shaft.

Product Features:

Chrome plated steel
1969-Up Big Block Chevrolet
For engines with 5/8¿ water pump shaft
For engines with 5/8┐ water pump shaft

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$5.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$45.49

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$28.49

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$9.99

This is a high quality gasket that will seal that leaking water neck, and provide you with years of service. This gasket works well in all applications.

Product Features:

Made From Cellulose/Nitrile Composition
Provides Excellent Sealing And Durability
These Gaskets Are Die Cut For a Precision Fit
Fits Small Block Chevy V8 Engines 1955-’90
Fits Big Block Chevy V8 Engines 1965-’90
Fits Small Block Chrysler 318/360 1979-’92
Fits Small Block Chrysler 3.9L/5.2L/5.9L Magnum 1992-’03

from

$75.99

Made of chrome plated steel. Smooth top with original equipment height and internal baffle. Features one breather/oil filler cap opening per valve cover. Hardware and gaskets sold separately.

Product Features:

Fits 1960-1986 Chevy 262-400 Small Block
OEM height, short-style covers
Chrome plated steel construction
Perimeter style bolt pattern
Features 1 breather/oil fill cap opening per valve cover
Sold as a pair

from

$329.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$60.99

This gear test fixture features variable rpm and oil pressure control allowing MSD engineers the ability to maintain the exact conditions that they want for gear tests. Severe loads can be placed on the gear and the fixture can spin up to 10,000 rpm. Features increased outer hardened layer thickness (RC 55-60). Micro polished surface for smooth contact. Proprietary formulated ductile iron. Melonite QPQ coated reduces friction and initial wear. Interstitial carbide concentration improves wear resistance and running properties.

Product Features:

Increased outer hardened layer thickness (RC 55-60)
Micro Polished Surface For Smooth Contact
Proprietary formulated ductile iron.
Melonite QPQ coated reduces friction and initial wear
Interstitial carbide improves wear resistance/running properties

from

$62.99

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$32.49

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$1076.99

If you think the torque of that monster diesel is something to brag about then you should feel it with the extra power of NOS. This kit works with stock and modified applications. Vehicles with computer upgrades will benefit even more as nitrous will aid in a clean combustion. Comes complete with 10 pound bottle, bottle brackets, nitrous feed line, large nitrous solenoid, electrical wiring and complete instructions.

Product Features:

Provides Additional Air Your Diesel Wants
Additional 50 HP
w/No Fuel System Or Electronic Upgrades
Complete Kit For Easy Installation

from

$116.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$231.99

Designed for most big block Chevrolet applications, the low profile sump design allows increased oil capacity without restricting ground clearance. Specially designed internal trap door baffling, combined with custom oil pump pick-ups, keep oil pressure fluctuation to a minimum. These oil pan measure 8-1/4 inch deep from the top side rail to bottom sump, and feature bright orange paint finish. For both street and racing applications. Oil pan capacity is 6 quarts.

Product Features:

Additional oil capacity – 6 Quarts
Superior oil control due to internal trap door baffle
Good ground clearance
Prepainted bright orange
Depth of Oil Pan: 8-1/4″
Width of Oil Pan: 8-3/8″
Length of Oil Pan: 22-3/4″

from

$367.99

The K&N AirCharger 63-1007-1 air intake system replaces your vehicle’s restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten air flow. This allows your vehicle’s engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 63-1007-1 air intake places a round K&N high-flow air filter directly on top of the throttle body allowing large volumes of air to be pulled into the engine delivering a guaranteed gain in horse power. The oversized air filter is capped with an impressive chrome lid for added visual appeal under the hood. This air intake is relatively easy to install using commonly available tools. Not legal for sale or use in California on any pollution controlled motor vehicle.

Product Features:

Guaranteed horsepower gain
Designed to improve throttle response and engine sound
Free-flowing high density polyethylene tube
Replaces entire factory air intake system
K&N No-Hassle Lifetime Limited Warranty
Easy to install, usually in 60 minutes or less
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$456.99

The BDX hand-held performance tuner gives drivers the edgepower they need, whether tackling tough terrain, pulling a heavy payload, or maximizing fuel economy on the highway. Its sleek design, full-color display, and customizable gauges help track and adjust powertrain performance to deliver more horsepower and torque when it’s needed most. Cloud-based tune delivery over built-in WiFi means that the BDX will always be running the latest tuning – enabling drivers to stay one step ahead of the packÿ.

Product Features:

Monitor and display vehicle data using the on-screen virtual gauges.
Preloaded, street-tested, dyno-proven tunes boost horsepower, torque, and throttle sensitivity.
Reads and clears DTC (Diagnostic Trouble Codes) with ease
Product might not be available in all states due to local laws.

from

$921.99

HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$126.99

Spectre’s Engine Dress-Up Kit was designed for the ’58-’86 Chevrolet small block 265-400. This kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stainless steel braided PCV hose with red/blue Magna-Clamps. Designed for use with OE specifications for fit and function, Spectre products are engineered to perform as good as they look.

Product Features:

For Chevrolet small block 265 and 400
Kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stain
Designed for use with OE specifications for fit and function
Made from high quality material

from

$32.49

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

These Are Have A Zinc Dichromate Finish
Tall Hex Head Bolt To Prevent Slippage
Extra Thick Parallel Ground Washer
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$223.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 11/32″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$95.99

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features: