from

$44.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$407.99

Automobiles in the 21st century have replaced the more conventional throttle cable technology for an ECM (Electronic Control Module) that translates pedal travel into electronic signals in order to provide power to the wheels. The ETC system (Electronic Throttle Control), also known as drive-by-wire, has the unfortunate downside of delayed throttle response and subdued acceleration, creating problems in certain circumstances such as up-hill starts, quick gear changes, overtaking, etc. The Sprint Booster aims to overcome this throttle response delay for ETC-equipped vehicles, providing crisp on-tap acceleration at the driver’s disposal.

Product Features:

Reduces Throttle Response Time
Improves Acceleration
Easy To Install
Does Not Affect The Vehicles Electronic System

from

$13.79

GM Genuine Parts Fuel Injector and Insulator Retainer Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$14.99

GM Genuine Parts Fuel Injector Clips are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$36.99

GM Genuine Parts Fuel Injection Fuel Rail O-Ring Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$6.29

GM Genuine Parts Fuel Pressure Relief Valve Caps are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$61.99

CARQUEST’S line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the U.S.A. Each injector is 100% tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function. Each injector includes new external seals and O-rings.

Product Features:

Each unit is 100% tested to OE specifications
Includes new O-rings and seals made of premium OE quality materials
Includes application specific technical bulletin, where applicable

from

$54.99

CARQUEST’S line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the U.S.A. Each injector is 100% tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function. Each injector includes new external seals and O-rings.

Product Features:

Each unit is 100% tested to OE specifications
Includes new O-rings and seals made of premium OE quality materials
Includes application specific technical bulletin, where applicable

from

$9.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$33.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$145.99

GM Genuine Parts Mass Air Flow (MAF) Sensors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These sensors are key parts of the engine management system, and are GM-recommended replacements for your vehicle’s original components. The MAF sensor measures the amount of air entering the engine so that the engine control module can determine the amount of fuel to inject. This helps ensure the most efficient air/fuel mixture for the best fuel economy and power. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Measures the amount of air entering the engine so the ECM can determine the amount of fuel to inject
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$108.99

GM Genuine Parts Mass Air Flow (MAF) Sensors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These sensors are key parts of the engine management system, and are GM-recommended replacements for your vehicle’s original components. The MAF sensor measures the amount of air entering the engine so that the engine control module can determine the amount of fuel to inject. This helps ensure the most efficient air/fuel mixture for the best fuel economy and power. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Measures the amount of air entering the engine so the ECM can determine the amount of fuel to inject
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$111.99

GM Genuine Parts Fuel Injector Rail Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$7.99

CARQUEST fuel injector seal kits include the necessary O-rings and seals to properly reseal the injector, which is a recommended practice any time the injector is removed. Each kit services one injector and includes hard to find or previously dealer-only components.

Product Features:

Premium OE quality materials
Services one injector

from

$29.99

GM Genuine Parts Fuel Injector Seal Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These seals help provide liquid-tight connections between the fuel injector and related components. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Helps provide a seal to prevent fuel leaks
Helps seal combustion chamber from the elements
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$116.99

GM Genuine Parts Fuel Injection Cut-off Valves are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$129.99

This premium tool kit is designed to ensure the correct installation of the combustion seal on Gasoline Direct Injectors (GDI), which require replacement any time the injector is reinstalled. This special tool allows for the expansion of the combustion seal to allow installation onto the injector’s tip and resizing tools to provide precise dimensioning to ensure proper combustion sealing. Constructed of high-quality stainless steel the tool will provide years of trouble-free service and can be used on over 100 unique styles of GDI injectors.

Product Features:

Includes two expansion cones
Includes two resizing tools
Includes one seal installation collet
Includes hard case
Includes instruction manual

from

$549.99

The Carquest line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the USA. Injectors are thoroughly tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function.

Product Features:

Includes eight premium fuel injectors
Each unit is 100% tested to OE specifications
Includes new o-rings and seals made of premium OE quality materials
Includes application specific technical bulletin, where applicable

from

$93.99

This fuel injection fuel feed pipe is designed to match the fit and function of the original pipe on specified applications, and is engineered for reliable performance and durability.

Product Features:

Direct replacement – this fuel injection fuel feed pipe is designed to match the fit and function of the original pipe on specified applications
Restores functionality – reliable replacement for an original part that has failed due to heat or vibration
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience