from

$1059.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$64.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
50 State Street Legal

from

$139.99

Product Features:

Head: 4.370″ Bore/0.039″ Thick/9.70cc Vol.
Intake: 1.82″x2.54″ Port/.060″ Thick
Exhaust: 1.940″ Round Port
5/16″ Valve Cover
Multi Piece Configuration

from

$75.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$44.99

Product Features:

Replacement Gasket Set For PN[4242]

from

$65.99

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated Aluminum
O-ring To Prevent Leaks
Swivels For Hard To Fit Applications
Comes With Allen Head Bolts

from

$19.49

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

8″ diameter
1970-73, 396-427-454 cu. in.
1967-69, 302 cu. in.
1965-68, 327 cu. in. hi-performance
1970-76, 400 cu. in.
1970-73, 350 cu. in.

from

$337.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$266.99

Product Features:

Non-Rotator
1.500 in. Outside Diameter
1.082 in. Inside Diameter
1.340 in. Coil Blind
Set of 16

from

$819.99

Product Features:

Great For Street Machines/Street Rods/Muscle Cars
Two Piece Design
Individual D-Shaped Runners
Optimized For Broad Power Range/Large Plenum Area
Can Be Used For Blow-Through Superchargers
Fully CNC Machined For A Perfect Fit
No Exhaust Crossover

from

$28.49

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$395.99

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
287/304 Advertised Duration, 235/249 Duration @ .050″, .510″/.495″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$10.99

10 Degree Superlock Steel Retainer for 1.250" OD Valve Spring

from

$22.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$9.99

This is a high quality gasket that will seal that leaking water neck, and provide you with years of service. This gasket works well in all applications.

Product Features:

Made From Cellulose/Nitrile Composition
Provides Excellent Sealing And Durability
These Gaskets Are Die Cut For a Precision Fit
Fits Small Block Chevy V8 Engines 1955-’90
Fits Big Block Chevy V8 Engines 1965-’90
Fits Small Block Chrysler 318/360 1979-’92
Fits Small Block Chrysler 3.9L/5.2L/5.9L Magnum 1992-’03

from

$126.99

Spectre’s Engine Dress-Up Kit was designed for the ’58-’86 Chevrolet small block 265-400. This kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stainless steel braided PCV hose with red/blue Magna-Clamps. Designed for use with OE specifications for fit and function, Spectre products are engineered to perform as good as they look.

Product Features:

For Chevrolet small block 265 and 400
Kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stain
Designed for use with OE specifications for fit and function
Made from high quality material

from

$20.79

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$57.99

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$101.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$13.99

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

from

$223.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features: