from

$226.99

Product Features:

FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

from

$41.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$30.19

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$38.59

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$29.99

Product Features:

Timing Chain Only

from

$103.99

Spectre’s Oil Pan was designed for Ford cars and 2WD trucks with 221, 260, 289, & 302W engines (will not fit vans and 4WD vehicles). The stock 4 quart capacity pan features a raw finish and durable steel construction. Precision engineered for optimum fit and function, this high quality OEM replacement part is easy to install.

Product Features:

For Ford cars and 2WD trucks with 221, 260, 289, & 302W engines
Stock 4 quart capacity
Raw, unfinished steel construction
Does not fit vans and 4WD vehicles

from

$361.99

The Edelbrock part #41603 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications and have a Black finish. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. Made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Small Block Ford 221-351W 62-95
Tall
Black Aluminum
Set Of Two

from

$97.99

This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:

Relocate oil filter to an easy access location

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$75.99

High Energy Pushrods from COMP Cams are an affordable, high quality solution when building street rods, RVs and daily drivers. High Energy Pushrods have a durable one-piece construction that meets or exceeds all OE pushrod specifications and fit perfectly with High Energy and Magnum Rocker Arms.

Product Features:

5/16″ diameter, 6.881″ length for Small Block Ford 255 and 302, ’65-up with Flat Tappet Cam
Best choice when building street rods, RVs or daily drivers
Meet or exceed all OE pushrod specifications
Mate perfectly with High Energy and Magnum Rockers
Durable one-piece construction

from

$63.09

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:

Contains all the gaskets needed to change out your camshaft
Fuel Injector O-Ring Not Included
Meets Performance Standards

from

$32.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$21.79

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

6 3¿8″ diameter
6 3┐8″ diameter
289-302-351 cu. in.
Increased Performance
Set Valve Lash At Proper Time

from

$1113.99

Product Features:

Designed To Add Power In Stages
Softens The Hit Of The Nitrous System
Control Excessive Tire Spin
Control Violent Chassis Reaction
Allows You To Adjust The 1st Stage

from

$42.49

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$30.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$48.49

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

Extra Thick Contact Arms
Large Radius Tungsten Contacts
High Strength Phenolic Rubbing Blocks
Prevents Points Float
Moisture-Proof Buna-N Condenser

from

$593.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Absolutely The Most Accurate Way To Trigger The Ignition
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.
Incl. brackets/mounting hardware to fit a variety of engines

from

$499.99

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

Certified Billet Material
Borg and Beck Clutch Pattern
Long-Style Clutch Pattern
Ring Gear Securely Mounted To Prevent Spinning

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$164.99

Edelbrock part #1146 is a Generator Bracket kit for our 1109, ’49-53 Ford Flathead Triple Deuce Intake Manifold. It is for those using the manifold in conjunction with a stock style generator. The purpose of kit is to remedy the interference between the g

Product Features:

Offset Bracket
Longer Fan Belt Is Required
Includes 1.25 in. Water Neck
Natural Finish
Made In The USA

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features: