Ford Maverick Performance Distributors

The e-curve distributor will drop right in your Ford 289/302 and fire up its performance. The e-curve distributor features a digital control module that manages the timing curve replacing the centrifugal advance springs and weights. This module lets you select from nearly 100 different advance curves, including a vacuum advance by turning two rotary dials. You can also set an rpm limit that will protect your engine from overrev damage caused by a missed shift or driveline failure. These distributors are also fit with a high-output ignition module so there is no need to run an external ignition box. This combination makes these distributors ideal for restored muscle cars and street rods to keep a stock or clean appearance under the hood. The e-curve distributor is topped with MSD’s rynite molded cap and rotor and is supplied with a heavy-duty gear and a matching 3-pin weathertight wiring harness.

Product Features:

• Digitally controlled; stand-alone distributor.
• Adjustable Electronic Advance w/Vacuum Advance
• Select up to 100 different curves through two rotary dials
• High output ignition module for a powerful spark
• Set a rev limit to protect your engine from overrev damage

Fits Ford 289 – 302 (5.0). Utilizing the durable and dependable High Energy Ignition (HEI) system pioneered by GM, these distributors avoid the unsightly wiring of stock Ford electronic ignition systems by installing this one-piece distributor with an internally positioned coil and module. Easy to install: just connect one 12-volt hot wire to the distributor (has optional tach hook-up). These units offer calibrated advance curves that are optimized for maximum combustion efficiency and for the elimination of detonation damage and throttle ping. Assembled from precision-madeparts for advance curve smoothness. Offers longer term durability and a higher voltage spark that permits a bigger spark plug gap, resulting in more power and reduced plug fouling. Each unit includes a high-power coil, a premium hi-dielectric cap with brass terminals, and a low-saturation ignition module. By eliminating the stock-Ford ballast resistor, more ignition voltage results in improved spark. Incorporates easily found High Energy Ignition (HEI) replacement parts. Assembled with upper and lower bushings (stock Ford distributors have only a single bushing). Technical Note: Gear not compatible with roller cams. If using roller cams, please contact the cam manufacturer for proper gear selection.

Product Features:

• Street/Strip Version
• Built-In Coil with Magnetic Trigger
• Features Red Cap
• Fits Ford 289-302 5.0 Engines
• Comes with An Iron Gear and with Not Work with Factory Roller Cams

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky duration systems or ancient breaker point models. These distributors come complete and Ready-to-Run. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs.

Product Features:

• Now includes built-in Rev Limiter
• Built-in module produces a 7.5 amp single spark through high rpm
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• Vacuum advance canister for improved economy (can be locked out)
• CNC machined billet aluminum housing and billet aluminum base
• Housing Is 5/8 in. Smaller In Diameter Than Stock Ford Distr.
• Maintenance-free magnetic pickup and precision reluctor
• Creates stable trigger signals throughout the rpm range
• Polished steel shaft is guided by a sealed ball bearing
• Advance plate and weights are fine blanked from chrome moly steel
• QPQ coated for friction reduction
• Mech. advance assem. can be locked out for crank trigger systems

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

• CNC machined billet aluminum housing and DuPont Rynite base
• Supplied w/Cap-A-Dapt and rotor (accepts MSD socket style caps)
• Must Be Used w/An MSD Ignition Control
• Mech. advance assem. can be locked out for crank trigger systems
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate
• Advance plate and weights are fine blanked from chrome moly steel
• QPQ coated for friction reduction

MSD engineers fit all of their high performance distributor experience into a special compact housing designed to be less obtrusive for Ford engines. The diameter of the special cap and housing are 5/8 inch smaller than stock Ford distributors providing extra room in front of the engine. The new MSD cap features spark plug style terminals and is firmly screwed down to the housing. The distributor relies on MSD’s race proven magnetic pick-up and precision reluctor to deliver accurate trigger signals to the MSD ignition throughout high rpm. The reluctor assembly is turned by a hardened steel shaft which rides in a sealed ball bearing for high rpm stability and endurance. Mounted to the top of this shaft is a fully adjustable mechanical advance assembly. The rate at which the chromoly assembly advances the timing is easily controlled by changing the supplied advance springs and stop bushing for total advance.

Product Features:

• Billet housing 5/8 in. smaller dia. than stock Ford distributors
• Must Be Used w/An MSD Ignition Control
• Supplied w/small dia. cap w/HEI style terminals; race and rotor
• Will accept PN[8441] Cap-A-Dapt
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate
• Mech. advance assem. can be locked out for crank trigger systems
• Advance plate and weights are fine blanked from chrome moly steel

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

Product Features:

• Equipped w/Steel Gear
• CARB E.O. Approved
• Does not require an MSD Ignition Control
• Supplied w/small dia. cap w/HEI style terminals; race and rotor
• Will accept PN[8441] Cap-A-Dapt
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate
• Mech. advance assem. can be locked out for crank trigger systems

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Designed w/Performance In Mind
• High Quality Material
• Stainless Terminals

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

MSD molds our most popular V8 distributor caps in-house. These caps are injection molded from DuPont? Rynite material and feature spark plug-style terminals. These terminals offer improved locking connections and the Rynite material is extremely strong with excellent dielectric properties. Plus, most caps have an optional wire retainer that is supplied with these caps to lock the wires in place.

Product Features:

• Designed w/Performance In Mind
• High Quality Material
• Stainless Terminals
• Performance replacement part

All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.

Product Features:

• Injection Molded From DuPont Rynite Material
• Extreme strength; high dielectric properties
• Designed with performance in mind
• High quality; voltage insulating material
• Brass terminals
• Black in color

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.

Product Features:

• Made from hi-performance 60 KV rated alkyd molding compound.
• Cap and rotor kits include nylon rotor hold-down screws.
• Flame-Thrower dust covers provide a larger air gap around the coil.

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.

Product Features:

• Made from hi-performance 60 KV rated alkyd molding compound.
• Cap and rotor kits include nylon rotor hold-down screws.
• Flame-Thrower dust covers provide a larger air gap around the coil.

Chrome plated steel. Includes hold-down bolt or stud. Holds the distributor in place for accurate timing. Serrated bottom prevents the distributor from turning.

Product Features:

• Rolled Edges For Strength
• Ideal For Magnetos
• Ideal For Ignition Distributor

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.

Product Features:

• Made from hi-performance 60 KV rated alkyd molding compound.
• Cap and rotor kits include nylon rotor hold-down screws.
• Flame-Thrower dust covers provide a larger air gap around the coil.

This gear test fixture features variable rpm and oil pressure control allowing MSD engineers the ability to maintain the exact conditions that they want for gear tests. Severe loads can be placed on the gear and the fixture can spin up to 10,000 rpm. Features increased outer hardened layer thickness (RC 55-60). Micro polished surface for smooth contact. Proprietary formulated ductile iron. Melonite QPQ coated reduces friction and initial wear. Interstitial carbide concentration improves wear resistance and running properties.

Product Features:

• Increased outer hardened layer thickness (RC 55-60)
• Micro Polished Surface For Smooth Contact
• Proprietary formulated ductile iron.
• Melonite QPQ coated reduces friction and initial wear
• Interstitial carbide improves wear resistance/running properties

Rotor for Flame-Thrower cast distributors. Premium rotor with brass contact

Product Features:

• PerTronix D660701 Rotor Flame-Thrower Billet Distributor
• Rotor for Flame-Thrower cast distributors

Performance mechanical advance springs.

Product Features:

• PerTronix D700700 Advance Spring Kit Flame-Thrower Billet Distributor
• Performance mechanical advance springs.

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

• Replacement Distributor Gear