Ford Granada Distributors

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Driveworks offers a line of aftermarket parts and accessories that are commercially acceptable and competitively priced, which provides professional technicians and DIYers with an affordable alternative for repairs.

The cap and rotor of any ignition system must be considered mainte­nance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these Cap and Rotor Replacement Kits.

A distributor’s performance is only as good as its drive gear. MSD Performance has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. MSD engineers have built test fixtures and spent hundreds of hours testing and evaluating the metallurgy of our gears. The result is a special alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance.

This gear is less prone to wear even with high-volume oil pumps.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Flame Thrower Street/Strip distributors have a speciallFlame-Thrower Street/Strip distributors have a specially designed HEI distributor module and coil combination which operates without misfire beyond 7500 RPM. That’s nearly 3000 RPM higher than most stock HEI Distributors. Race HEI Distributors feature an electronic HEI Distributor module and 50,000 volt coil combination that optimizes spark energy and peak current to the spark plug in the 6000 to 8500 RPM range.y designed module and coil combination which operates without misfire beyond 7500 RPM

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

BWD SELECT designs, specifies, and manufactures replacement parts with one goal in mind-make them the very best. To maximize performance and longevity, we use the finest materials and improve on OE specifications, whenever possible.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

This distributor drive gear is designed to match the fit, function and appearance of the original part on specified vehicles, and is engineered for durability and reliable performance.

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

MSD’s Ready-to-Run Ford Distributors are the perfect upgrade for bulky DuraSpark systems or ancient breaker point models. These distributors come complete and ready-to-run. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance.

The Pro-Billet Distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place. Each model is supplied with a high-quality cap with brass terminals for full spark delivery, heavy-duty rotor and a special gear to work with the factory camshafts.

Edelbrock part No. 22758 Max-Fire distributor for Ford 351W V-8 engines is ready to run right out-of-the-box and are the perfect upgrade for your ignition system. They’re ideal for replacing or upgrading from a points triggered distributor. They feature precision machining for a perfect fit along with a simple three wire hook up for an easy installation with no need to run an external ignition control box. The centerless ground shaft utilizes an upper sealed roller bearing with an extra long lower bronze Oil-Lite bushing for smooth operation. The high output magnetic pickup and large paddle wheel reluctor deliver a strong trigger signal at high RPM for maximum performance. All of these features allow Max-Fire distributors to provide unrivaled voltage to the coil, ensuring that you’re getting maximum performance from your engine. We recommend a new Max-Fire coil for maximum voltage output, ensuring you get the most from your high performance engine at higher RPM’s. Each distributor includes a cap, rotor, retainer and mechanical advance curve kit.

TSP’s HEI Distributor has everything you need, all under one cap. With a high-quality aluminum housing and hardened steel dual bushing construction, it is built to last. It features fully adjustable mechanical and vacuum advances, meaning precision is a breeze. It has a high-output module, high-spark 65,000 volt coil, solid brass terminals, and an easy one-wire hookup. So, if you’re looking to switch that Windsor from EFI to carbureted, look no further for your ignition set-up.

TSP Ready to Run Distributor offers performance and convenience at a great price. It features a CNC-machined billet aluminum body and hardened steel shaft, with a sealed ball bearing on top and a sintered steel bushing on the bottom. Its easy-to-change module means you won?t need to use an external ignition box, and its small size will fit most applications. It has a clip-on cap with solid brass terminals and a color-matched wire retainer.

This special com­bination of bronze and nickel creates high-strength gear teeth that are less prone to wear even with high-volume oil pumps.