Ford F-350 Distributors

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

“Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “”arc-thru”” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.”

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system or operating system fault.

This special com­bination of bronze and nickel creates high-strength gear teeth that are less prone to wear even with high-volume oil pumps.

A distributor’s performance is only as good as its drive gear. MSD Performance has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. MSD engineers have built test fixtures and spent hundreds of hours testing and evaluating the metallurgy of our gears. The result is a special alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

This distributor drive gear is designed to match the fit, function and appearance of the original part on specified vehicles, and is engineered for durability and reliable performance.

MSD Bronze Distributor gears are machined from quality AMPCO 45 aluminum bronze containing 5% nickel. This com­bination of bronze and nickel creates high-strength gear teeth that are less prone to wear even with high-volume oil pumps.

Mallory Distributor Gears are precision machined from alloy steel in our factory to exacting original equipment specifications. Special attention is given to the heat treating requirements of each gear to assure the proper hardness, giving trouble free service when used with proferal billet (hydraulic and mechanical flat tappet) and selectively austempered ductile iron billet (hydraulic roller tappet) camshafts. Available for Mallory, original equipment, and other distributors.

“Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “”arc-thru”” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.”

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Flame Thrower Street/Strip distributors have a speciallFlame-Thrower Street/Strip distributors have a specially designed HEI distributor module and coil combination which operates without misfire beyond 7500 RPM. That’s nearly 3000 RPM higher than most stock HEI Distributors. Race HEI Distributors feature an electronic HEI Distributor module and 50,000 volt coil combination that optimizes spark energy and peak current to the spark plug in the 6000 to 8500 RPM range.y designed module and coil combination which operates without misfire beyond 7500 RPM

TSP’s HEI Distributor has everything you need, all under one cap. With a high-quality aluminum housing and hardened steel dual bushing construction, it is built to last. It features fully adjustable mechanical and vacuum advances, meaning precision is a breeze. It has a high-output module, high-spark 65,000 volt coil, solid brass terminals, and an easy one-wire hookup. So, if you’re looking to switch that Windsor from EFI to carbureted, look no further for your ignition set-up.

TSP HEI Distributor has everything you need, all under one cap. With a high-quality aluminum housing and hardened steel dual bushing construction, it is built to last. It features fully adjustable mechanical and vacuum advances, meaning precision is a breeze. It has a high-output module, high-spark 65,000 volt coil, solid brass terminals, and an easy one-wire hookup.

A legend returns – the tried and true Mallory Unilite Distributor line is back! The easy three wire hookup of the Unilite makes running a stock coil, a Mallory performance coil and even a Mallory HyFire CD ignition a snap. Supplied with a quality cap and rotor, the Mallory Unilite also provides a fully adjustable mechanical advance to dial in the perfect timing curve for a multitude of engine combinations. The Unilite features a compact housing that lends itself well to applications where space is a premium due to tight firewall clearance or blower applications.

TSP Pro Series Ready to Run Distributor is perfect for a street performance upgrade. It features a CNC-machined billet aluminum body and hardened steel shaft, with a sealed ball bearing on top and a sintered steel bushing on the bottom. It also comes with a fully adjustable mechanical advance, vacuum advance, magnetic pickup trigger, and a high-output circuit board module with digital tach output. The dielectric cap comes with solid brass terminals and a color-matched wire retainer.

A distributor’s performance is only as good as its drive gear. MSD Ignition has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. MSD engineers have built test fixtures and spent hundreds of hours testing and evaluating the metallurgy of our gears. The result is a special iron alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance.

A distributor’s performance is only as good as its drive gear. MSD Performance has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. MSD engineers have built test fixtures and spent hundreds of hours testing and evaluating the metallurgy of our gears. The result is a special alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance.