Ford F-250 Pickup Differentials

Yukon positraction internals for Dana 44 Dura Grip posi, 30 spline. Does not include clutches. Does NOT fit Trac Loc or Powr Lok. Fits Dura Grip ONLY.

Product Features:

• Spider gear kit
• Fits Dana Spicer 44 with Dura Grip positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 35 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1992 and down Dana Spicer 44 IFS
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Product Features:

• Carrier shims for Dana Spicer 60 and 70U

8.8″ Reverse inner pinion bearing oil baffle.

Product Features:

• Oil baffle
• Fits Ford 8.8″ IFS

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Standard Open & TracLoc cross pin shaft for 10.25″ Ford.

Product Features:

• Cross pin shaft
• Fits Ford 10.25″

Product Features:

• Clutch kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Smooth design

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

aFe Powers new rear differential cover brings performance engineering to the protection of your axles differential. This differential cover is constructed out of durable die cast aluminum with reinforced ribs and wrinkle black powder coating for maximum strength and styling. This cover comes with all necessary hardware and includes an O-ring for a leak free seal. This cover has about a 5 quart lube capacity at the factory line; factory cover holds about 4 quarts. Built-in internal and external fins transfer heat from the fluid to the outside air for maximum cooling. This system incorporates a large magnetic drain and fill plug that captures loose particles for maximum rear-end protection. Pre-installed large oil level sight glass with calibration plug set to the factory fluid level to eliminate overfilling.

Product Features:

• 5 Quart Lube Capacity
• Built In Internal/External Fins
• Magnetic Drain Plug
• Optional Accessories Available

55P Chevy Passenger Drop Out gasket.

Product Features:

• Side gear thrust washer
• Fits Ford 10.25″

Product Features:

• MINI INSTALL KIT FORD 8.8

Product Features:

• Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Fits reverse rotation Dana Spicer 44
• 8.50″ ring gear diameter
• 26 spline pinion
• 10 ring gear bolts
• 4.11 ratio

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Product Features:

• KIT SHIM

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 10.25″ & 10.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 10.25″ and 10.5″
• Includes carrier bearings and races and “super” carrier shim kit

Product Features:

• Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

ZIP locker front switch cover.

Product Features:

• Cover for switch
• Front

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″