from

$31.49

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$6.99

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

Application matched components ensure the charging system can be returned to like new condition.

from

$4.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$221.99

Carquest Starters with 100% NEW construction will restore hard working vehicles to exceed OE specified performance & endurance. All new units and components offer unmatched performance, reduce downtime & customer comebacks. Carquest HD alternators are primed to keep you moving forward. Built to perform in severe duty environments where consistent efficient high outputs are required.

Product Features:

Product Features:

Contains Innovative Brush-less and Premium Brush Components that have been tested and certified for highest possible power output
Stator – wound to OE specifications. Heavy coated Polyester wire provides consistent conductivity
Premium Transpo rectifiers use 13mm press fit Diodes for maximum performance
Rotor shafts CNC machined & precision balanced to eliminate vibration
Over-Voltage shutdown limits voltage if output terminal is disconnected form the battery
Load dump protection ensures transient voltage spikes do not damage transistor
Improved power transmission with lower engine speed keeps accessories and powered implements running at maximum output without additional load to the engine.

from

$13.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$42.99

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

from

$131.99

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

from

$28.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$35.99

The Starter Solenoid is the relay of the starting circuit that carries the high amperage required when the starter motor is engaged. The solenoid is typically energized by the starter switch when commanded by the vehicle operator. Starter solenoids may also be used in other high amperage circuits, compare solenoid specification to your circuit needs before installing.

Product Features:

Application matched component to ensure the system can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$214.99

Bosch Premium Starters are designed, built and tested to provide the ultimate in performance and reliability

Product Features:

Premium 100% New Starter
Our new and reman starters and alternators are designed to perform equal to or better than the original equipment parts, that they replace
Our new and reman starters and alternators are designed to be identical in fit and performance to original equipment parts
Our new and reman starters and alternators utilize the latest manufacturing technologies and highest quality parts to ensure the best performance and longest life

from

$191.99

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
All new components are utilized to ensure long service life
Internal electronics are upgraded for heavy duty reliability (where applicable)
Armatures and commutators are 100% load tested
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$45.99

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure confidence and product reliability, every time.

from

$18.99

LockSmart® is a specialized aftermarket lock brand featuring door, trunk, and ignition lock cylinders. LockSmart® provides OE fit, form, and function locks across domestic and import applications for both late and older model vehicles.

Product Features:

Direct-fit OE replacement ignition lock cylinder ensures effective start of engine energy supply
Constructed from high-grade materials to ensure durability and longevity
Undergoes 100% testing for proper fit, form, and function
As a global manufacturer, we maintain complete quality control throughout the manufacturing process

from

$19.49

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$20.99

The starter motor is responsible for rotating the engine during the starting process. The electric starter motor has several serviceable parts making repair economical when single part replacement will suffice.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Application matched component to ensure the system can be returned to like new condition.

from

$19.99

MOTOR – WINDOW

from

$11.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$2.29

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$24.05

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
Our starter solenoids have more pure copper windings than found on most vehicles to create a stronger magnetic field
Our polyester-insulated magnet wire, cadmium-plated copper discs and solid contact bolts reduce voltage drop and deliver full battery power to the starter while providing greater protection against electrical overload
Pure copper battery terminal studs reduce resistance to permit higher current flow, even in the hottest environments, for better performance
We understand and expect the demand for quality, our starting and charging system products feature high grade materials for extended service life
BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

from

$31.49

Driveworks offers a line of aftermarket parts and accessories that are commercially acceptable and competitively priced, which provides professional technicians and DIYers with an affordable alternative for repairs.

Product Features:

Direct-fit OE replacement ensures ease of installation
Designed to meet OE performance
As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need
As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need

from

$25.49

Product Features:

Designed to OE standards for ease of installation
Contain more pure copper windings than found on most vehicles and create a stronger magnetic field in even the hottest environments for better performance.
Solenoids contain cadmium-plated copper discs and solid contact bolts reduce voltage drop to deliver full battery power to the starter and have pure copper battery terminal studs that reduce resistance and permit higher current flow.

from

$55.99

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features: