from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$14.99

Dana 60 semi-float C-clip.

Product Features:

C-clip
Fits Dana Spicer 60

from

$324.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 70HD
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$38.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1960-2015
Weight approx: 3 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
NO STUDS

from

$6.99

Product Features:

Oil baffle for Dana Spicer 60 and Dana Spicer 70U

from

$519.99

Yukon replacement standard open carrier case for Dana 80, 4.10 & up (NOT ABS) 35 & 37 spline.

Product Features:

Standard open carrier case
Does not include spider gears
Fits Dana Spicer 80 with 35 or 37 spline axles
4.10 and up ratio only
Not compatible with ABS applications

from

$275.99

Product Features:

DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$17.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$19.99

Product Features:

Pinion preload shims for Dana Spicer 60 and 70U

from

$51.99

Yukon 1330 U/Joint with zerk fitting. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$8.99

Replacement crush sleeve for Dana 60, APROX 0.660″ long.

Product Features:

Crush sleeve for Dana Spicer 60
0.660″ tall

from

$5.99

Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.

Product Features:

Pinion gear thrust washer for Dana Spicer 60
Fits standard open and Trac Loc applications

from

$235.99

Yukon replacement yoke for Dana 80 with a 1480 U/joint size. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 80
37 spline
1480 u-joint size
4.188″ snap ring span
1.375″ cap diameter
Outside snap ring design
Strap style

from

$21.99

Replacement pinion seal for Dana S135.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Dana Spicer S135

from

$1537.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$27.99

Ensure a leak-free repair when servicing axle bearings or parking brake shoes. This axle shaft flange seal is a direct replacement for the original gasket and should be replaced every time work is performed at the axle flange.

Product Features:

Product Features:

Ideal replacement – this axle shaft flange seal directly replaces the original gasket without having to visit the dealer
Required for routine service – this gasket should be replaced every time work is performed at the axle flange
Durable construction – this axle shaft flange gasket is made of tough, durable materials for leak-free performance
Quality tested – this flange gasket has been designed and tested for a guaranteed fit

from

$121.99

Product Features:

Complete shim kit for Dana Spicer 80
4.375″ O.D. pinion bearing application only

from

$45.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$7.99

AxleHubBolt

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$69.99

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

Cross pin shaft
Fits Dana Spicer 70 and 80

from

$444.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 80 with 4.375″ O.D. pinion bearing
Fits 1998 and up Fords
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and silicone.