Ford E-250 Econoline Performance Ignition Products

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

• Bolt-on Performance
• Factory replacement coil

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Fd-478
• MSD 5527
• Standard Motor Products SMP Fd-478
• MSD 5527
• Resists Shock And Vibration
• Resists Corrosion

The improved spark energy and voltage of MSD’s blaster 2 coils, combined with reliability, have made them a favorite for performance enthusiasts. Whether firing a restored BOSS 429 or a Saturday night circle tracker, the blaster 2 has always gotten the job done. MSD is excited to offer blaster coils for late model Ford engines with coil-on-plug technology. The new blaster COPs are designed as a direct bolt-in replacement coil for many SOHC Modular Motors. The housing and installation are the same as the factory, but that’s where the similarity ends. Inside the MSD red housing, engineers spec’d better material to assemble the primary and secondary windings. There is also patented dual magnet technology to step up the output. Together, this combines a coil that produces higher voltage and spark energy. The coil-on-plug design of the blaster COPs puts the spark energy right out of the coil and across the plug gap to improve the combustion and output of the engine. The blaster 2 COPs are available individually or as a complete set of eight.

Product Features:

• Fits 1999-2004 4.6L/5.4L SOHC 2V
• Improved Spark Energy And Voltage Output
• Patented Winding Design and Materials
• Direct Bolt-In to Factory Connectors

ACCEL Super Coils feature advanced bobbin technology, highly specialized silicon magnetic steel cores, optimized windings, proper resistance and engineered turn ratios that deliver a high performance, quality coil. Specialized high temperature epoxy resists shock and vibration, while increasing thermal conductivity. These are direct high performance replacements for OEM coils.

Product Features:

• Specialized silicone magnetic steel cores are surrounded by precision wrapped windings using advanced bobbin technology which helps maintain the proper resistance and turn ratios necessary to deliver improved performance spark
• Advanced Bobbin Technology
• Direct Plug In Replacement results in a Direct OE Fit
• OBD ll Safe, so you won’t be throwing codes, just sparks
• Standard Motor Products SMP Fd-508
• MSD 8243 82438
• Resists Shock And Vibration
• Resists Corrosion

The improved spark energy and voltage of MSD’s blaster 2 coils, combined with reliability, have made them a favorite for performance enthusiasts. Whether firing a restored BOSS 429 or a Saturday night circle tracker, the blaster 2 has always gotten the job done. MSD is excited to offer blaster coils for late model Ford engines with coil-on-plug technology. The new blaster COPs are designed as a direct bolt-in replacement coil for many SOHC Modular Motors. The housing and installation are the same as the factory, but that’s where the similarity ends. Inside the MSD red housing, engineers spec’d better material to assemble the primary and secondary windings. There is also patented dual magnet technology to step up the output. Together, this combines a coil that produces higher voltage and spark energy. The coil-on-plug design of the blaster COPs puts the spark energy right out of the coil and across the plug gap to improve the combustion and output of the engine. The blaster 2 COPs are available individually or as a complete set of eight.

Product Features:

• Fits 2005-2009 4.6L And 5.4L 3V
• Improved Spark Energy And Voltage Output
• Patented Winding Design and Materials
• Direct Bolt-In to Factory Connectors

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1983 thru 1996.

Product Features:

• Fits Most Stock And Modified Distributors
• Dwell Control Circuit
• Resists False Triggering

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford TFI Remote Mounted modules. 1991-95

Product Features:

• Fits Most Stock And Modified Distributors
• Dwell Control Circuit
• Resists False Triggering

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Product Features:

• Service Part
• Makes Connections Quick And Easy

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

• Absolutely the most accurate way to trigger the ignition
• The non-magnetic pickup cannot be false triggered.
• Powerful magnets are embedded in a billet aluminum trigger wheel.
• Incl. brackets/mounting hardware to fit a variety of engines

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps