from

$30.99

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Ford 7.5″, 8.8″, 9″ and 10.25″

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$32.99

Product Features:

Crush sleeve spacer for Ford 9.75″
0.280″ tall

from

$47.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$94.99

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

Side adjuster
Fits Ford 9″
3.062″ designs only

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$275.99

8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.

Product Features:

Clutch kit
Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction

from

$128.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 44 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 44
Includes carrier bearings and races and carrier shim kit

from

$774.99

Yukon Trac Loc positraction, Ford 8.8″, 31 spline, with Carbon Fiber clutches.

Product Features:

Trac Loc positraction carrier case
Includes spider gears
Fits Ford 8.8″ with 31 spline axles
Carbon fiber clutches

from

$188.99

Product Features:

Spider gear kit
Fits Ford 9.75″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$12.99

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

Roll pin for Dana Spicer 30 and Dana Spicer 44
0.235″ diameter

from

$83.99

Product Features:

Seal housing for Dana Spicer 44
Includes o-rings

from

$11.99

Pilot bearing retainer for Ford 9″.

Product Features:

Pilot bearing retainer for Ford 9″

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 44

from

$349.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9.75″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$8.99

Pinion seal for 7.5″, 8.8″, and 9.75″ Ford, and also 1985-’86 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Ford 7.5″, 8.8″ and some 9.75″
2.785″ O.D.

from

$4.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$5.99

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
7/16″ head
.925″ long

from

$199.99

This differential bearing kit includes all necessary installation components for a differential ring and pinion on certain vehicle years, makes and models.

Product Features:

Convenient kit – this ring and pinion bearing installation kit includes all necessary components for a complete repair on certain vehicle applications
Related repair – smart to have on hand when installing a differential ring and pinion
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$215.99

9″ Ford HD 6061 aluminum pinion support, Daytona, PLAIN-SILVER, NO races.

Product Features:

Fits Ford 9″ with 28 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
6061 aluminum
Does not include races

from

$947.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features: