Ford Bronco Carburetor

Carburetor for a Ford Bronco

Use the fitment form at the top of the page to select your exact year and engine type for your Ford Bronco.

• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7295)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  5.0

  Read 2 review(s)

  Review snapshot ® by PowerReviews

  5.0

  5.0

  • 5

    5

    2012-01-12

    5

    5

    Performs as well as OEM

    Performs as well as OEM

    Submitted 2012-01-12

    By 1970Econo

    From Denver, Colo.

    Carefully packaged to prevent damage. No trouble returning core for deposit credit. Carburetor came with everything pictured and purchased. However, it should also have included the anti-stall dashpot and shield with heater-hose rack for proper operation of the thermostatic spring.

    Bottom Line recommended

    Carefully packaged to prevent damage. No trouble returning core for deposit credit. Carburetor came with everything pictured and purchased. However, it should also have included the anti-stall dashpot and shield with heater-hose rack for proper operation of the thermostatic spring.

    By 1970Econo from Denver, Colo.

    BOTTOM LINE recommended

  • 5

    5

    2010-01-19

    5

    5

    The carb was in great condition.

    The carb was in great condition.

    Submitted 2010-01-19

    By The RC pilot

    From Waxhaw, NC

    This carb came in great condition (reman). Installed in a 1971 Ford pickup. But wish it would have come with setup condition. Finally found setup in old manual.

    Bottom Line recommended

    This carb came in great condition (reman). Installed in a 1971 Ford pickup. But wish it would have come with setup condition. Finally found setup in old manual.

    By The RC pilot from Waxhaw, NC

    BOTTOM LINE recommended

  from $186.99

  View Product
• 

  Edelbrock - Performer 1406 Carburetor: 600 CFM,4-Barrel, Square Bore,Electric Choke, Single Inlet, Satin Finish (Part No. 1406)

  Description

  
  
  Product Features:

  • Burnished Aluminum
  • GM/AMC-Style Throttle Linkage
  • Electric Choke Installed from Factory
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet

  4.5

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  4.5

  4.5

  • 5

    5

    2020-07-28

    5

    5

    I recommend this carb for a street engine like my 389.

    I recommend this carb for a street engine like my 389.

    Submitted 2020-07-28

    By James

    From Undisclosed

    This carb fit directly to my 1965 pontiac GTO four barrel intake with only the gaskets and stiffener plate used. Car started and ran great with factory carb settings. Love it.

    Bottom Line NULL

    This carb fit directly to my 1965 pontiac GTO four barrel intake with only the gaskets and stiffener plate used. Car started and ran great with factory carb settings. Love it.

    By James from Undisclosed

    BOTTOM LINE NULL

  • 2

    2

    2019-06-30

    2

    2

    Extremely difficult to install

    Extremely difficult to install

    Submitted 2019-06-30

    By Rusty

    From Powder Springs, GA

    72 Gran Torino 429ci Only thing that fit was the 4 mounting bolts to manifold, Linkage hits manifold and wont move, none of the connection are the same having to modify everything. I have been working on this carburator for 2 days still not hooked up, now according to manual I need to order a throttle lever kit, throttle cable plate, transmission linkage, new longer fuel lines the are on opposite side from original. will need to spend additional $100 to get this thing to work (I hope)

    Bottom Line not recommended

    72 Gran Torino 429ci Only thing that fit was the 4 mounting bolts to manifold, Linkage hits manifold and wont move, none of the connection are the same having to modify everything. I have been working on this carburator for 2 days still not hooked up, now according to manual I need to order a throttle lever kit, throttle cable plate, transmission linkage, new longer fuel lines the are on opposite side from original. will need to spend additional $100 to get this thing to work (I hope)

    By Rusty from Powder Springs, GA

    BOTTOM LINE not recommended

  • 5

    5

    2018-06-23

    5

    5

    outstanding

    outstanding

    Submitted 2018-06-23

    By gerry

    From north ton. ny

    works flawless right out of the box

    Bottom Line recommended

    works flawless right out of the box

    By gerry from north ton. ny

    BOTTOM LINE recommended

  from $364.99

  View Product
• 

  Edelbrock - Performer 1405 Carburetor: 600 CFM,4-Barrel, Square Bore,Manual Choke, Single Inlet, Satin Finish (Part No. 1405)

  Description

  
  
  Product Features:

  • Burnished Aluminum
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet

  4.5

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  4.5

  4.5

  • 5

    5

    2014-10-22

    5

    5

    Great Carb

    Great Carb

    Submitted 2014-10-22

    By Dustin

    From Texas

    I bought this carb for my SBC 350, on a 72 Nova. Fit up great to my Edelbrock Performer Intake Manifold. If you are tossing between the Manual and Electric choke, just consider how much an electric choke costs to replace if and when it goes bad. I had tossed with getting the 650CFM, but finally decided on the 600 so I wouldn't go overkill on gas and hurt my performance. I must say this carb was the best solution. Replacing my Rochester style Quadrajet with this carb increased the performance quite a bit. Just follow the instructions with the carb, and enjoy it.

    Bottom Line recommended

    I bought this carb for my SBC 350, on a 72 Nova. Fit up great to my Edelbrock Performer Intake Manifold. If you are tossing between the Manual and Electric choke, just consider how much an electric choke costs to replace if and when it goes bad. I had tossed with getting the 650CFM, but finally decided on the 600 so I wouldn't go overkill on gas and hurt my performance. I must say this carb was the best solution. Replacing my Rochester style Quadrajet with this carb increased the performance quite a bit. Just follow the instructions with the carb, and enjoy it.

    By Dustin from Texas

    BOTTOM LINE recommended

  • 5

    5

    2014-01-17

    5

    5

    good deal for the $

    good deal for the $

    Submitted 2014-01-17

    By moon

    From Wilmington NC

    best part for the best price

    Bottom Line recommended

    best part for the best price

    By moon from Wilmington NC

    BOTTOM LINE recommended

  • 5

    5

    2013-11-18

    5

    5

    first class top shelf good to go!!!

    first class top shelf good to go!!!

    Submitted 2013-11-18

    By clydesdale

    From va. beach, va.

    i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!

    Bottom Line recommended

    i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!

    By clydesdale from va. beach, va.

    BOTTOM LINE recommended

  from $334.99

  View Product
• 

  Edelbrock - Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No. 1825)

  Description

  New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.
  
  Product Features:

  • Spring Loaded Needles/Seat Increase Performance
  • New Qwik-Tune Adjustable Secondary Air Valve
  • Distinctive Black Accented Hardware
  • Lightweight Ball-Burnished Aluminum
  • No Gaskets Below Fuel Level to Prevent Leakage
  • Metering Rod/Step Up Springs Can Be Changed Easily
  • GM/AMC-Style Throttle Linkage

  4.5

  Read 2 review(s)

  Review snapshot ® by PowerReviews

  4.5

  4.5

  • 4

    4

    2014-04-25

    4

    4

    Performance Enhancer

    Performance Enhancer

    Submitted 2014-04-25

    By none

    From Pine, Colorado

    Please read AND understand all the instructions that are packaged with the unit BEFORE starting the installation. Obtain all the "other" parts and pieces that you may need before replacement

    Bottom Line recommended

    Please read AND understand all the instructions that are packaged with the unit BEFORE starting the installation. Obtain all the "other" parts and pieces that you may need before replacement

    By none from Pine, Colorado

    BOTTOM LINE recommended

  • 5

    5

    2013-05-03

    5

    5

    Edelbrock Off-Road Carb

    Edelbrock Off-Road Carb

    Submitted 2013-05-03

    By Tornado

    From Clay City, KY

    Put carb on rock crawler. Climb lots of hills and the carb works great. No loss of fuel when climbing steep grade. Does what I bought it to do.

    Bottom Line recommended

    Put carb on rock crawler. Climb lots of hills and the carb works great. No loss of fuel when climbing steep grade. Does what I bought it to do.

    By Tornado from Clay City, KY

    BOTTOM LINE recommended

  from $411.99

  View Product
• 

  Edelbrock - Performer 1407 Carburetor: 750 CFM,4-Barrel, Square Bore,Manual Choke, Single Inlet, Satin Finish (Part No. 1407)

  Description

  
  
  Product Features:

  • Burnished Aluminum
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet

  4.5

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  4.5

  4.5

  • 4

    4

    2013-08-16

    4

    4

    Good workhorse of a product.

    Good workhorse of a product.

    Submitted 2013-08-16

    By PDUBS

    From Cincinnati Ohio

    Simple installation, no leaks, not tempermental.

    Bottom Line recommended

    Simple installation, no leaks, not tempermental.

    By PDUBS from Cincinnati Ohio

    BOTTOM LINE recommended

  • 4

    4

    2013-05-06

    4

    4

    good

    good

    Submitted 2013-05-06

    By 69 c10

    From spring hill fl

    This is a overall very good product

    Bottom Line recommended

    This is a overall very good product

    By 69 c10 from spring hill fl

    BOTTOM LINE recommended

  • 5

    5

    2012-05-06

    5

    5

    Good product

    Good product

    Submitted 2012-05-06

    By Chevy man

    From Temple,tx

    Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was turn my idle screw up about 1/2 turn runs perfect. Also it costs way less than the holley, great buy

    Bottom Line recommended

    Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was turn my idle screw up about 1/2 turn runs perfect. Also it costs way less than the holley, great buy

    By Chevy man from Temple,tx

    BOTTOM LINE recommended

  from $382.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7583)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  4.5

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  4.5

  4.5

  • 5

    5

    2014-05-27

    5

    5

    Great Carb/Like New

    Great Carb/Like New

    Submitted 2014-05-27

    By Old-Man

    From Cincinnati, Ohio

    Don't be afraid of this one! It looks new, hooked up like the factory one and started right away. No adjustments needed.Used on a farm truck/work horse.

    Bottom Line recommended

    Don't be afraid of this one! It looks new, hooked up like the factory one and started right away. No adjustments needed.Used on a farm truck/work horse.

    By Old-Man from Cincinnati, Ohio

    BOTTOM LINE recommended

  • 5

    5

    2010-12-01

    5

    5

    Excellent bang for the buck

    Excellent bang for the buck

    Submitted 2010-12-01

    By Clayton

    From Cheyenne, Wyoming

    It arrived in a very durable packaging and even came with the replacment seal. The instructional paperwork it came with leaves a lot to be desired; however, a quick search on line and I found what I needed. The truck I bought was modified so I had a tough time not knowing where hoses went when there weren't any to begin with. No fault of Advance though.

    Bottom Line recommended

    It arrived in a very durable packaging and even came with the replacment seal. The instructional paperwork it came with leaves a lot to be desired; however, a quick search on line and I found what I needed. The truck I bought was modified so I had a tough time not knowing where hoses went when there weren't any to begin with. No fault of Advance though.

    By Clayton from Cheyenne, Wyoming

    BOTTOM LINE recommended

  • 4

    4

    2010-07-06

    4

    4

    Carburetor - Remanufactured

    Carburetor - Remanufactured

    Submitted 2010-07-06

    By Bertoo

    From Roanoke, VA

    Nice fit.

    Bottom Line recommended

    Nice fit.

    By Bertoo from Roanoke, VA

    BOTTOM LINE recommended

  from $233.99

  View Product
• 

  Holley - Street Avenger; Carburetor (Part No. 0-80670)

  Description

  Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
  
  Product Features:

  • Vibratory Polished For Good Looks
  • Optimized Street Calibration That Works Out Of The Box
  • Factory Preset Electric Choke For Easy Startups
  • Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
  • No Unnecessary Trips Back To The Parts Store
  • Limited Lifetime Warranty
  • 100% Wet Flow Tested By Holley Technicians
  • Arrives Ready To Run

  4.0

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  4.0

  4.0

  • 5

    5

    2018-04-04

    5

    5

    i would buy again

    i would buy again

    Submitted 2018-04-04

    By keith

    From undisclosed

    great carb

    Bottom Line NULL

    great carb

    By keith from undisclosed

    BOTTOM LINE NULL

  • 1

    1

    2013-08-01

    1

    1

    TROUBLES

    TROUBLES

    Submitted 2013-08-01

    By Scott

    From Gainesville , Fl

    Install the street avenger on my truck was fine for around 100 miles and then started smelling raw gas seen gas leaking from the secondary throttle shaft now have to send it in for warranty what a piece of trash

    Bottom Line not recommended

    Install the street avenger on my truck was fine for around 100 miles and then started smelling raw gas seen gas leaking from the secondary throttle shaft now have to send it in for warranty what a piece of trash

    By Scott from Gainesville , Fl

    BOTTOM LINE not recommended

  • 3

    3

    2012-10-27

    3

    3

    Easy Install

    Easy Install

    Submitted 2012-10-27

    By John Wayne

    From Blount County, Tn.

    This carburetor was instaled on a pickup that is driven mostly on weekends. It was very easy to instal I am having issues with fast idle and choke adjustment.

    Bottom Line not recommended

    This carburetor was instaled on a pickup that is driven mostly on weekends. It was very easy to instal I am having issues with fast idle and choke adjustment.

    By John Wayne from Blount County, Tn.

    BOTTOM LINE not recommended

  from $495.99

  View Product
• 

  Edelbrock - AVS2 1906 Carburetor: 650 CFM,4-Barrel, Square Bore,Electric Choke, Single Inlet, Satin Finish (Part No. 1906)

  Description

  The Edelbrock #1906 AVS2 Series 650 cfm carburetor is the next generation in Edelbrock carburetors. Designed and calibrated for optimum street performance in small-block and some big-block engines. The AVS2 features annular flow primary boosters with a ne
  
  Product Features:

  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Electric Choke Type
  • 650 cfm Maximum Flow Rating

  3.5

  Read 3 review(s)

  Review snapshot ® by PowerReviews

  3.5

  3.5

  • 1

    1

    2020-12-31

    1

    1

    Junk

    Junk

    Submitted 2020-12-31

    By Repair man

    From New York

    Junk save your money buy a Holley

    Bottom Line not recommended

    Junk save your money buy a Holley

    By Repair man from New York

    BOTTOM LINE not recommended

  • 5

    5

    2020-07-31

    5

    5

    Tbi

    Tbi

    Submitted 2020-07-31

    By Tooner

    From Milwaukee

    This thing hits like a fuel injection edelbrock has a beautiful thing going with these, if only they had secondary power rings also that you could buy aftermarket to retro from the stream type injection I would probably buy 2

    Bottom Line recommended

    This thing hits like a fuel injection edelbrock has a beautiful thing going with these, if only they had secondary power rings also that you could buy aftermarket to retro from the stream type injection I would probably buy 2

    By Tooner from Milwaukee

    BOTTOM LINE recommended

  • 5

    5

    2019-08-12

    5

    5

    Edelbrock's best carburetor yet!

    Edelbrock's best carburetor yet!

    Submitted 2019-08-12

    By Gary T.

    From East TN

    I have a 1988 Ford Ranger with a highly modified 302 & have been using a model #1825 AVS Thunder 650 "off road" carb for over 10 years, but I recently decided to try the new AVS2 I've been hearing so much about. Wow! What a difference. The annular boosters are no joke! The AVS2 is a more streetable carb in my application! My truck is more responsive, smoother when pulling out, & gas mileage has improved. So far, I'm extremely pleased!

    Bottom Line recommended

    I have a 1988 Ford Ranger with a highly modified 302 & have been using a model #1825 AVS Thunder 650 "off road" carb for over 10 years, but I recently decided to try the new AVS2 I've been hearing so much about. Wow! What a difference. The annular boosters are no joke! The AVS2 is a more streetable carb in my application! My truck is more responsive, smoother when pulling out, & gas mileage has improved. So far, I'm extremely pleased!

    By Gary T. from East TN

    BOTTOM LINE recommended

  from $378.99

  View Product
• 

  Edelbrock - Reman Performer Carb #9936 800 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No. 9963)

  Description

  Product Features:

  • Satin Finish
  • 4 Barrel
  • Aluminum Body Material
  • Electric Choke Type
  • 800 cfm Maximum Flow Rating

  from $467.99

  View Product
• 

  Edelbrock - Performer 14063 Carburetor: 600 CFM,4-Barrel, Square Bore,Electric Choke, Single Inlet, Black Finish (Part No. 14063)

  Description

  The Edelbrock 14063 Performer Series 600 CFM electric choke black powder coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day.
  
  Product Features:

  • Black Powder Coated Finish
  • 4 Barrel
  • Annular Booster Type
  • Electric Choke Type
  • 600 cfm Maximum Flow Rating

  from $460.99

  View Product
• 

  Edelbrock - Performer 14073 Carburetor: 750 CFM,4-Barrel, Square Bore,Manual Choke, Single Inlet, Black Finish (Part No. 14073)

  Description

  The Edelbrock 14073 Performer Series 750 CFM manual choke black powder coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. S
  
  Product Features:

  • Black Powder Coated Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 750 cfm Maximum Flow Rating

  from $445.99

  View Product
• 

  Edelbrock - Performer 14053 Carburetor: 600 CFM,4-Barrel, Square Bore,Manual Choke, Single Inlet, Black Finish (Part No. 14053)

  Description

  The Edelbrock 14053 Performer Series 600 CFM manual choke Black Powder Coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. S
  
  Product Features:

  • Black Powder Coated Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 600 cfm Maximum Flow Rating

  from $416.99

  View Product
• 

  Edelbrock - Performer Carburetor #9962 800 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No. 9962)

  Description

  Product Features:

  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Electric Choke Type
  • 800 cfm Maximum Flow Rating

  from $369.99

  View Product
• 

  Edelbrock - Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No. 9913)

  Description

  Product Features:

  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Electric Choke Type
  • 750 cfm Maximum Flow Rating

  from $367.99

  View Product
• 

  Edelbrock - AVS2 1905 Carburetor: 650 CFM,4-Barrel, Square Bore,Manual Choke, Single Inlet, Satin Finish (Part No. 1905)

  Description

  The Edelbrock #1905 AVS2 Series 650 cfm carburetor is the next generation in Edelbrock carburetors. Designed and calibrated for optimum street performance in small-block and some big-block engines. The AVS2 features annular flow primary boosters with a ne
  
  Product Features:

  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 650 cfm Maximum Flow Rating

  from $345.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7773)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $339.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7295A)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $302.79

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7796)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $285.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7665)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $269.99

  View Product
• 

  United Carb - Remanufactured Carburetor 1 Barrel (Part No. 7-7587)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $251.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7669)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $251.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7551)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $233.99

  View Product
• 

  Tomco Carb - Carburetor - Remanufactured (Part No. T6-863)

  Description

  Remanufactured in the U.S.A. for optimum performance and fuel economy, Tomco brand carburetors are renowned as the ultimate replacement for your vehicle's original equipment. Completely disassembled and cleaned, every component is thoroughly evaluated. Non-qualifying components are replaced and design flaws corrected based upon our extensive research. Every carburetor is flow tested to simulate actual vehicle conditions and adjusted to the original equipment manufacturer's specifications. Experience and care assures that you will receive the highest quality carburetor which meets or exceeds the performance of your vehicle's original equipment.

  from $199.99

  View Product
• 

  United Carb - Remanufactured Carburetor 2 Barrel (Part No. 7-7322A)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $199.99

  View Product
• 

  United Carb - Remanufactured Carburetor 1 Barrel (Part No. 7-7327)

  Description

  Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

  from $159.99

  View Product