Excalibur Phaeton Performance and Racing Products
Top Excalibur Phaeton Performance and Racing Products Categories
We carry over 119 Performance and Racing Products in inventory for the Excalibur Phaeton. If you’re looking for aftermarket Performance and Racing Products for your Excalibur Phaeton, check out all these categories:
Essential Excalibur Phaeton Performance and Racing Products
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)
from
$31.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1818)
from
$27.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2918)
from
$43.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)
from
$37.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
Competition Cams – XE Computer Control 206/212 Hydraulic Flat Cam/Lifter Kit (Part No.CL12-249-4)
from
$390.99
SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
Product Features:
See More
Product Features:
- Cam and lifter kit for Small Block Chevy engines
- CL-Kit includes cam, lifters, assembly lube, instructions and decals
- HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
- 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
- Valve spring upgrade required
Competition Cams – Cam & Lifter Kit, Bbc 295T Big Mutha Thumpr Hyd 1 Kt (Part No.CL11-602-4)
from
$937.99
BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
Product Features:
See More
Product Features:
- Cam and lifter kit for Big Block Chevy engines
- CL-Kit includes cam, lifters, assembly lube, instructions and decals
- HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
- 295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
- Valve spring upgrade required
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)
from
$51.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1037)
from
$64.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)
from
$159.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.
Product Features:
See More
Product Features:
- Complete Kit: Includes Retainers And Locks
- Springs Made of Highest Quality Spring Wire
- Springs Precision Wound To Close Tolerances
- Includes Superior Quality Steel Retainers
- Includes 7 deg. Heat-Treated Valve Stem Locks
- Retainers and Locks Black Oxide Coated
- Non-Rotator Style: Dyno Tested and Street Proven
- Great Match to Edelbrock Camshaft Kit
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)
from
$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1410)
from
$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Competition Cams – Xtreme Energy 224/230 Hydraulic Flat Cam (Part No.11-242-3)
from
$259.99
HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.
Product Features:
See More
Product Features:
- HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.
- 268/280 Advertised Duration, 224/230 Duration @ .050″, .515″/.520″ Lift, 110 Lobe Separation
- Valve spring upgrade required
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam (Part No.11-250-3)
from
$259.99
HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.
Product Features:
See More
Product Features:
- HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.
- 284/296 Advertised Duration, 240/246 Duration @ .050″, .574″/.578″ Lift, 110 Lobe Separation
- Valve spring upgrade required
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Edelbrock – Performer RPM AIR-Gap Small Block Chevy Polished Intake Manifold (Part No.75011)
from
$749.99
Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Dual-plane high-rise intake. For square bore carburetors only. For street and high performance use. Available in cast, polished or endurashine finish.
Product Features:
See More
Product Features:
- Polished Version Of Edelbrock PN[7501]
- Polish is Hand-Buffed for Brilliant Shine
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock – Performer Intake Manifold Small-Block Chevy (Part No.3706)
from
$401.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes and Accepts EGR
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 9 Piece Set (Part No.1212)
from
$27.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
B & M – Automatic Shifter, Street Bandit Shifter (Part No.80797)
from
$869.99
The ultimate shifter for automatic transmission equipped street vehicles! The Hi-Tek Street bandit has all the same feature as the above Street Bandit line of shifters, with an interchangeable billet knob design.
Product Features:
See More
Product Features:
- Ideal For High-Tech Pro-Street
- Ideal For High-Tech Street Rods
- Narrow Styled Aluminum Housing
- Includes Neutral Safety Switch
- Includes Backup Light Switch
- Includes Billet Aluminum Knob
- Can Be Used w/Reverse Pattern Valve Body
Excalibur Phaeton Performance and Racing Products Categories
Helping You Find the Right Performance and Racing Products for Your Excalibur Phaeton
You love your Phaeton. So we’ve made it easier than ever to help you find Excalibur Phaeton Performance and Racing Products in our online catalog. Our inventory holds 119 aftermarket and OEM Performance and Racing Products for your Excalibur Phaeton, ranging from $9.99 to $2,298.00.
We offer parts from 5 brands trusted to make quality Performance and Racing Products for your Excalibur Phaeton. Before you buy, take some time to read through customer reviews. We currently have 2,287 reviews of Excalibur Phaeton Performance and Racing Products from previous customers. Some of the top rated parts include Big Mutha’ Thumpr 243/257 Hydraulic Flat Cam/Lifter Kit with 4.1 stars and Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.7 stars.
Find your Phaeton Performance and Racing Products here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Excalibur Phaeton part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Performance and Racing Products Brands for Your Excalibur Phaeton
Our inventory holds Performance and Racing Products for your Excalibur Phaeton from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, FEL-PRO Performance, and Holley, all of which can keep that Excalibur happy.
We have FEL-PRO Performance parts available for your Excalibur Phaeton in categories like Performance Engines. Some of the top-rated FEL-PRO Performance parts in these categories are:
from
$64.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets
from
$44.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Top-Rated Holley Performance and Racing Products
Leading Holley Performance and Racing Products
We carry Holley brand parts for your Excalibur Phaeton across several catalog categories, including Performance Fuel Systems. Some of our most reviewed Holley parts include:
from
$509.99
(45)
Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny
Performance Carburetors
from
$699.99
(6)
Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny
Performance Carburetors
FAQs for Excalibur Phaeton Performance and Racing Products
What are the most purchased Performance and Racing Products for the Excalibur Phaeton?
Out of 119 Performance and Racing Products for the Excalibur Phaeton, the most popular in our inventory are:
from
$195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
from
$42.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
from
$27.99
This product is not rated
Lower Intake Manifold Gasket Set: 9 Piece Set
Performance Engine Intake Manifold Gaskets
What are the top-rated Excalibur Phaeton Performance and Racing Products?
Top-rated Performance and Racing Products for your Excalibur Phaeton based on customer reviews/ratings are:
from
$914.99
(13)
Big Mutha’ Thumpr 243/257 Hydraulic Flat Cam/Lifter Kit
“Worked prefect. Gave me the Hi speed blower back”
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
from
$302.99
(4)
Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet
“I love this cam it gives me the power I need at the low end to pull havey loads where I need it the most for the work I do with my truck This cam and ”
