from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$509.99

Product Features:

Trac Loc positraction carrier case
Does not include spider gears
Fits Dana Spicer 60
4.10 and down ratio only
ABS and non-ABS compatible

from

$435.99

aFe Powers new front-end differential cover brings performance engineering to the protection of your trucks front-end. This differential cover has a 3-1/2 quart lube capacity (factory cover holds 2-1/2 quarts) at the factory fluid level line, a magnetic drain plug and a magnetic fill plug to remove unwanted debris. Built-in external fins transfer heat from the fluid to the outside air for maximum cooling. aFe has also designed a large oil level sight glass with calibration plug set to the factory fluid level to eliminate overfilling. This differential cover is constructed out of durable die-cast A380 aluminum with reinforced ribs and a wrinkle black powder-coating for maximum strength and style. When it comes to engineering for power, performance, protection and value, aFe Power is the only choice.

Product Features:

External Fins Transfer Heat To Atmosphere
Calibration Plug
Fill Plug w/Magnet At End Of Extended Stick
Magnetic Drain Plug

from

$439.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2010 and down GM and Chrysler 11.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$6.99

Product Features:

Oil baffle for Dana Spicer 60 and Dana Spicer 70U

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$596.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$41.99

11.5 GM spanner adjuster nut.

Product Features:

Side adjuster
Fits GM 11.5″

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$213.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

BRG MASTER KIT ’98 & LATER DANA 60 FORD W/TIMKEN

from

$143.99

Product Features:

MINI INSTALL KIT DANA 80

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$14.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$52.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Dana Spicer 60
Works with Spartan Locker or standard open spider gears

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$15.99

11.5″ GM standard Open pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer
Fits GM 11.5″

from

$1485.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM and Chrysler 11.5″ with 30 spline axles
Clutch style positraction
Smooth design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$12.99

GM 9.5″ ring gear bolt. 12mm x 1.5.

Product Features:

Ring gear bolt for GM 9.2″
12mm x 1.5

from

$799.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$704.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 60
9.75″ ring gear diameter
29 spline pinion
12 ring gear bolts
3.54 ratio

from

$188.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Included are a pinion seal, complete shim kit, marking compound and brush.

from

$254.99

Product Features:

BILLET HP 1350-29 SPLINE YOKE

from

$47.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft