Daewoo Nubira Transmission Fluids

Liqui Moly’s Leichtlauf High Tech 5W-40 is a fully synthetic, premium low-friction engine oil for all-season use in gasoline and diesel engines without diesel particulate filters (DPF). The combination of innovative base oils – based on synthesis technology and the latest additive technology – guarantees an engine oil that reduces oil and fuel consumption and that ensures fast lubrication of the engine. Depending on the manufacturer instructions, oil change intervals of up to 40,000 km are possible. Ideally suited for modern gasoline and diesel engines with multi-valve technology, turbocharger and with or without charge air cooling. Especially suitable where there are long intervals between changes and heavy duty engine requirements.

Product Features:

• All season use reliable at high and low temperatures
• Suited for modern gasoline and diesel engines with multivalve technology, turbocharger and with or without charge air cooling
• An engine oil that reduces oil and fuel consumption
• Ensures fast lubrication of the engine
• Made in germany
• Full Synthetic Oil Composition

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• MaxLife High Mileage Synthetic Blend Engine Oil is specially designed for engines with over 75,000 miles, providing greater protection and maximizing engine life.

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• Anti-wear additives: The oil contains anti-wear additives that defend critical engine components against wear and tear, reducing the risk of expensive repairs.

Liqui Moly’s Leichtlauf High Tech 5W-40 is a fully synthetic, premium low-friction engine oil for all-season use in gasoline and diesel engines without diesel particulate filters (DPF). The combination of innovative base oils – based on synthesis technology and the latest additive technology – guarantees an engine oil that reduces oil and fuel consumption and that ensures fast lubrication of the engine. Depending on the manufacturer instructions, oil change intervals of up to 40,000 km are possible. Ideally suited for modern gasoline and diesel engines with multi-valve technology, turbocharger and with or without charge air cooling. Especially suitable where there are long intervals between changes and heavy duty engine requirements.

Product Features:

• All season use reliable at high and low temperatures
• Suited for modern gasoline and diesel engines with multivalve technology, turbocharger and with or without charge air cooling
• An engine oil that reduces oil and fuel consumption
• Ensures fast lubrication of the engine
• Made in germany
• Low-friction formula: Leichtlauf LIQUI-MOLY Synthetic Engine Oil 5W-40 is a premium, fully synthetic engine oil that reduces oil and fuel consumption, thanks to its low-friction formula.

Modern transmissions are better than ever, with more gears to help improve fuel efficiency and acceleration. Greater performance calls for greater protection. Valvoline Extended Protection Full Synthetic ATF features our exclusive Dual Defense Additive Technology for two layers of protection against metal-on-metal contact and thermal breakdown, all while minimizing wear on clutch components. In fact, Valvoline Extended Protection Full Synthetic ATF is 45% stronger against breakdown compared to major brand DEX/MERC oxidative PDSC performance. Proven to maximize transmission life, our patented formula is suitable for use in 92% of vehicles in light duty automatic transmissions 2010 and newer. Keep your modern vehicle shifting smoothly, mile after mile, with the ultimate protection you can only expect from Valvoline, the #1 ATF brand.

Product Features:

• The ultimate protection for your automatic transmission
• 45% stronger against breakdown
• Dual Defense Additive Technology combines friction modifiers and anti-wear additives for two layers of protection
• Suitable for use in over 92% of vehicles in light duty automatic transmissions 2010 and newer

Fully synthetic high-performance transmission fluid. Offers high shear stability combined with correct friction behavior and excellent wear protection. Outstanding resistance to viscosity breakdown provides superior shift performance in all operating conditions. Suitable for a variety of manual transmissions.

Product Features:

• Excellent viscosity/temperature properties
• Outstanding seal compatibility
• Excellent resistance to aging
• Excellent wear resistance
• High pressure-absorption capability
• Wide viscosity range
• Reduces gearshift resistance
• Excellent corrosion protection
• Reduces transmission noise

Castrol® Transmax DEX/MERC includes enhanced friction durability for smooth transmission performance. Designed for use in older Ford and GM vehicles.

Product Features:

• Enhanced friction durability for smooth transmission performance
• Meets DEXRON®-III H requirements; also satisfies requirements of DEXRON®, DEXRON®-III, IIE, and II; do not use this ATF in applications calling for DEXRON®-VI
• Meets MERCON® requirements; may also be used in power steering applications where MERCON® is required; use Castrol Type F ATF in applications calling for Type F
• Do not use this ATF in applications calling for MERCON® V or MERCON® SP

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Castrol® Transmax® ATF/CVT Universal is a technologically advanced, full-synthetic formulation designed to deliver excellent performance in most traditional step-shifting automatic transmissions and continuously variable transmissions currently in use. It is also suitable for use in hybrids. It is blended with premium base oils and an additive package that utilizes Castrol Smooth Drive® Technology.

Product Features:

• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• ATF Applications: Dexron VI (Dexron III, Dexron), Mercon LV (Mercon SP, Mercon V, Mercon), JASO 1A (03), JASO 1A LV (13), Toyota T IV, Toyota T III, Toyota WS, Honda/Acura DW 1/Z 1, Nissan Matic D, Matic J, Matic S, Hyundai/Kia SP IV, SP III
• ATF Applications: Mazda ATF M-V, M-III, FZ, Mitsubishi SP IV, SP III, IIM, II, PA, J3, VW/Audi (6, 8 & 9 speed automatics), BMW/Mini (6, 8 and 9 speed automatics), Jaguar/Land Rover (6, 8 & 9 speed automatics), Porsche (6, 8 & 9 speed automatics)
• ATF Applications: Volvo (6, 8 and 9 speed automatics), Volvo Transmission Oil 97342, AT102, Mercedes-Benz (7 and 9 speed automatics)
• CVT Applications: Toyota CVT Fluid TC, Toyota CVT Fluid FE , Nissan CVT Fluid NS-1, Nissan CVT Fluid NS-2, Nissan CVT Fluid NS-3, Subaru i-CVT Fluid, Subaru i-CVT FG, Subaru Lineartronic High Torque Chain CVTF, Honda HCF-2

FRAM Global ATF is formulated to meet the fluid needs of a broad range of automatic  transmissions. Using advanced additive technology and base fluids, it is suitable for service fill of  many transmissions manufactured by North American, Asian, and European OEMs. FRAM  Global ATF provides oxidation and thermal stability, friction control, load-carrying ability, corrosion  and wear protection. It helps protect against the formation of sludge, varnish and foam. FRAM Global ATF has exceptional low temperature flow properties and enhanced protection  against viscosity breakdown at high temperatures. It also has exceptional oxidation and thermal  stability, resulting in maximum service life.

Product Features:

• Maintains friction control for smooth shift action and protection against shudder
• Retains high temperature viscosity resulting in maximum oil film thickness and  excellent wear
• Controls sludge, corrosion, and wear of gears
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings

Castrol® Transmax High Mileage is ideal for most transmissions with over 75,000 miles. It features additional seal conditioners to help stop leaks and cleaning agents to reduce varnish and deposit formation. It also protects against clutch wear and restores smooth shifting.

Product Features:

• Additional seal conditioners to prevent or help stop leaks
• Extra cleaning agents to reduce varnish and sludge formulation
• Protects against clutch wear
• Restores smooth shifting
• Greater frictional durability provides superior transmission performance
• Can be used in a wide variety of specifications including DEXRON«-IIIH, MERCON«áand JASO-1A.
• Can be used in a wide variety of specifications including DEXRON®-IIIH, MERCON® and JASO-1A.
• Exceeds all passenger car and light truck manufacturer¿s warranty requirements for vehicles, transmissions or power steering service where a DEXRON®-IIIH or MERCON® type ATF is specified
• Exceeds all passenger car and light truck manufacturer┐s warranty requirements for vehicles, transmissions or power steering service where a DEXRON«-IIIH or MERCON« type ATF is specified

Automatic Transmission Fluid – 5 Liter Bottle

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Valvoline Full Synthetic MaxLife Multi-Vehicle ATF, the No. 1 ATF product, suitable for use in 95% of vehicles. And now, it’s recommended for most belt & chain-driven continuously variable transmissions (CVT). Featuring advanced additives to prevent the major causes of transmission breakdown, it’s designed to help prevent leaks, reduce wear & tear, and maximize performance. Has improved thermal stability for longer fluid life, better viscosity stability for consistent transmission operation, and frictional enhancements for smooth gear engagements. Valv MaxLife Multi-Vehicle ATF is suitable for most Ford, GM, Toyota, Honda, Nissan, Hyundai, Subaru, BMW, Mercedes, Volvo, VW & Audi vehicles. Recommended for use in: GM DEXRON-II, DEXRON-III, DEXRON-VI, and DEX-CVT; Ford MERCON LV; Toyota/Lexus Type T, T-II, T-IV, WS, CVTF FE, and CVTF TC; Honda/Acura ATF-Z1 and Honda CVT; Nissan/Infiniti Matic-D, Matic-J, Matic-K and Matic-S; Hyundai/Kia SP-II, SP-III, SP-IV and SPH-IV; BMW 7045E, ETL 8072B, LA2634 and LT71141; Allison C-4; Mercedes-Benz NAG-1; Volvo 1161521, 1161540, 97340 and 1273.41; Subaru ATF HP, Lineartronic chain CVT and CVT-II, Lineartronic High Torque CVT, and CV-30; and VW/Audi G-052-025-A2 and G-052-162-A1. CURRENTLY UNABLE TO SHIP THIS PRODUCT TO CUSTOMERS LOCATED IN CALIFORNIA

Product Features:

• FOR USE IN 95% OF VEHICLES INCLUDING MOST CVTs in operation with US registered light duty applications
• HIGH PERFORMANCE CONDITIONING AGENTS prolong seal elasticity to prevent leaks
• IMPROVED DURABILITY & TRANSMISSION LIFE with anti-wear technology to avoid costly repairs
• ENHANCED HIGH & LOW TEMP PERFORMANCE supports transmission fluid in all weather situations