Chevrolet Luv Alternators and Starters

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Product Features:

• Brand may vary by location

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our knock sensors are designed to respond to knock frequencies up to 1000 Hz accommodating shifts in engine knock frequency making it a more flexible sensor responding to correct engine knock over a broad range of vehicle conditions
• Manufacturing processes include an automated data acquisition system to continuously monitor the sensor output to ensure that it responds with appropriate voltage output at the specified frequency range
• All units are 100% tested using an accelerometer vibration test to ensure trouble-free operation
• Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Carquest Starters take advantage of the power of 100% NEW to restore hard working vehicles to OE specified performance & endurance. All new units and components offer unmatched performance, reduce downtime & customer comebacks. Carquest Starters are primed to keep fleets moving forward. Built to perform in severe duty environments, with high output capabilities built in through improved technical & material formulas for high power output and efficient performance

Product Features:

• High quality components form the foundation our parts are built from. Transpo¿s innovative and high quality electronic technologies for internal components are incorporated to achieve high performance outputs.
• High quality components form the foundation our parts are built from. Transpo┐s innovative and high quality electronic technologies for internal components are incorporated to achieve high performance outputs.
• Power & Efficiency are designed into every component. No matter the ambient temperature, starters will provide maximum cranking power to get engines running.
• Connectors and power transmission components are highly resistant to extreme moisture environments because we use nickel plated contactors and double armature coating. We maintain a rigorous test schedule with endurance, salt spray, dirt and grime and out
• Integrated magnetic switch provides protection against weak power from batteries.
• Over-Crank Protection (OCP) Monitors heat in starter from over cranking & shuts down starter to prevent burning
• Precision design and machining are the Extreme vibration failure solution. Vehicles often perform in adverse conditions like extreme temperatures that create tolerance shifts that produce high frequency vibration, which leads to resistance in power transf

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

LockSmart® is a specialized aftermarket lock brand featuring door, trunk, and ignition lock cylinders. LockSmart® provides OE fit, form, and function locks across domestic and import applications for both late and older model vehicles.

Product Features:

• Direct-fit OE replacement ignition lock cylinder ensures effective start of engine energy supply
• Constructed from high-grade materials to ensure durability and longevity
• Undergoes 100% testing for proper fit, form, and function
• As a global manufacturer, we maintain complete quality control throughout the manufacturing process

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

This 50-amp alternator from WAI is engineered to deliver exceptional performance and reliability, making it a top choice for aftermarket replacements. Designed to meet or exceed OEM specifications, it ensures a perfect fit and hassle-free installation. The advanced voltage regulator protection safeguards against transient voltage spikes, preventing potential battery damage, while its low saturation voltage minimizes heat dissipation for enhanced durability. Featuring a high-power rectifier assembly with open junction press-fit diodes, this alternator is built to run cooler and last longer. Each unit is rigorously tested, and a printed copy of the test results is included, giving you confidence in its performance from the very first use. With WAI’s commitment to quality, this alternator is a dependable solution for maintaining your vehicle’s electrical system.

Product Features:

• Engineered to meet or exceed OEM specifications for a perfect fit and hassle-free installation.
• Voltage regulator protection – load dump protected against transient voltage spikes avoiding potential battery damage. Low saturation voltage results in lower heat dissipation. Fully compliant in communication with ECU.
• High power rectifier assembly is designed with higher power open junction press fit diodes to keep the units running cool.
• Each unit includes a printed copy of the test results so you know exactly what to expect from our parts right from the first time they power on.
• Built for enhanced durability, this alternator features advanced heat management through its low saturation voltage design, ensuring reliable performance and extended lifespan.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Regulators and rectifiers are 100% electronically load tested for reliable charging performance
• 100% new OE-quality brushes and bearings are used to ensure long service life
• Rotors and stators are load tested and double insulated for maximum charging performance
• Slip rings are precision polished for maximum brush contact and service life
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672