Chevrolet K1500 Performance Engines

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.

Product Features:

• Cam and lifter kit for Small Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.
• 268/268 Advertised Duration, 218/218 Duration @ .050″, .454″/.454″ Lift, 110 Lobe Separation
• Valve spring upgrade required

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Dyno Tested And Street Proven
• Great Match to Edelbrock Camshaft Kit

HYDRAULIC – Magnum: High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.

Product Features:

• HYDRAULIC – Magnum: High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.
• 270/270 Advertised Duration, 224/224 Duration @ .050″, .470″/.470″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Can be used with mild ratio rocker arms and traditional performance valve springs.

Product Features:

• 2000-6500 RPM Power Band
• Single Plane/Open Plenum Design
• No Provision For Divorced Or Hot Air Choke
• Square Flange Carburetor Mounting

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens at 160 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully opens at Correct Temperature Consistently Regardless of engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

This Mr. Gasket Deluxe Engine Bolt Kit includes chrome plated grade 5 hex head fasteners with AN type washers for the following: Intake Manifold, Timing Cover, Oil Pan, Fuel Pump, Water Neck, Long Water Pump and Headers. The AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome Plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

This Mr. Gasket Rear Main Seal is made from Viton&reg: Rubber. This style of rubber can handle high temperature like silicone rubber, but with superior abrasion resistance. Its durability and it’s double, offset lip seal design make it recommended for applications that have high engine vacuum, like racing engines that utilize external vacuum pumps for crankcase evacuation.

Product Features:

• Repairs That Leaky Rear Main Sail
• Viton« Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Viton® Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Upgrade for Rope Seal Equipped Cars or Silicone Rubber Main Seals

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
• Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
• For OE replacement, high performance street, drag race and oval track
• .187″ thick
• Handles Ex Flange Pressure
• Forms Leak Proof Seal
• Black Latex Coating

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Ultra Pro Magnum Rocker Arm Set with 1.6 Ratio for Chevrolet SBC with 7/16" Stud

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

These High Energy Die Cast Aluminum Roller Rocker Arms for Chevy V8 265-400 applications are perfect for street and moderate race use. With a 3/8″ stud diameter and 1.5 ratio, the die cast, larger-than-stock body of the rocker arms is made of aluminum for superior strength with light overall weight. High Energy Die Cast Aluminum Roller Rocker Arms from COMP Cams are an affordable option that feature a die cast, aluminum body with a needle bearing fulcrum and roller tip. Designed to be stiffer and more durable, these cost effective rocker arms are capable of providing added valve lift while withstanding the rigors of a performance application. Their specially engineered fulcrum and roller tip create far less friction than sliding factory models to lower oil temperatures, thus improving both response and horsepower. Snap rings are used to hold the trunion and bearings locked in place..

Product Features:

• Cost effective aluminum construction provides superior strength to weight ratio
• Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
• Durable design increases valve lift while withstanding the rigors of moderate race use
• Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.