Chevrolet Impala Cooling and Climate Controls

Product Features:

• Our units are all pre-aligned & pre-adjusted to save installation time and ensure proper switching.
• A lubricated felt pad that lubricates the cam lobes on the vehicles distributor. This reduces wear on the point set rubbing block, extending the usable life of the part.
• Ventilated where available, tungsten contacts, which run cooler and exhibit less erosion.
• The copper-alloy shunt provides superior resistance to breakage, due to the flexing of the moving arm on the point set. It also significantly increases current conductivity over typical steel, shunts.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Carquest Hose Assemblies are designed to carry refrigerant in an air conditioning system. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

• 100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
• Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
• Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
• Welds and crimps meet and exceed original equipment tension specifications.
• Manufactured to allow flexibility in the hose to conform to engine compartments.
• O-Rings necessary for installation are included.

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

This A/C compressor bypass pulley is a cost-effective solution to allow the original equipment drive belt to be used while bypassing an inoperable A/C compressor.

Product Features:

• Cost-effective solution – this bypass pulley retains the use of the standard drive belt after a failed A/C compressor is removed
• Durable components – this bypass pulley uses quality components for a long service life
• Easy to install – uses the same mounting points as the A/C compressor
• Quality tested – this part has undergone extensive testing to ensure a quality fit and long service life

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Blower motor resistor burnt out? Restore proper heating and cooling functionality with this direct replacement resistor designed to match the operation and performance of the original equipment on certain vehicles.

Product Features:

• Direct replacement – this blower motor resistor matches the fit, function and performance of the original motor on specific vehicles
• Restores performance – fixes a fan that’s only operating on one speed or not working at all
• Thoroughly tested – examined and validated to perform safely and effectively
• Trustworthy quality – backed by team of engineers and inspectors in the United States

High quality OE replacement part with all components needed to complete the job

Product Features:

• Galvanized steel construction
• Meets all requirements of international standard ISO 140
• Suitable for a wide variety of applications
• Set screw installation

This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:

• Ideal replacement – this engine coolant bleeder screw matches fit and function of the original equipment screw
• Durable materials – designed to withstand high cooling system temperatures and pressures
• Cost-effective solution – this bleeder screw offers original equipment quality at a competitive price
• Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

Replace your stock black engine pulleys with a pair of chrome plated steel pulleys from Mr. Gasket. The pulleys are highly polished then chrome plated for lasting beauty.

Product Features:

• Highly polished for lasting beauty

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design
• Manufactured for the sealing repair environment
• Validated for fit, form, and function
• Quality that you can trust

Optimized refrigerant flow; Core design meets or exceeds OE performance And efficiency; Application specific design for GM vehicles; Replaces damaged evaporator inlet tube

New Standard Replacement Heater Core

Product Features:

• Made Of Aluminum
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

HVAC Mode Door Actua

ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Protective outer coverings help provide long-lasting durability
• Color-coded wires allow for easy installation
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

Climate controls stopped working? Seamlessly restore operation by easily swapping the malfunctioning original module with this fully tested replacement unit.

Product Features:

• Direct replacement – this HVAC control module matches the appearance and function of the original unit on specific vehicles
• Functionality-tested – module has been tested to ensure the same operation as the stock module
• Simple installation – no advanced vehicle knowledge is required for proper installation and setup
• Trustworthy quality – backed by team of engineers and inspectors in the United States

Original equipment design provides exact fit and performance.

Product Features:

• Precise fitting sealing edges prevent leakage and premature cooling.
• Self-cleaning and self-aligning thermostat valve.
• Stainless steel assembly and springs are engineered for long life and smooth performance.

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

• Ideal for rigid cast aluminum parts
• Meets OEM Specifications
• Sensor safe & non-corrosive
• Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
• Blowout resistant, allowing leakproof gaskets to be made in just one minute
• Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
• Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
• Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
• Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

Adjustable Thermostatic Fan Control; Economy Model; 32-248°F. Controls the operating temperature of Imperial electric fans

Product Features:

• Economy adjustable thermostatic fan control
• Economy Model; 32-248°F
• For use with Imperial electric fans
• Probe installs into radiator fins

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
• Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
• OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

GM Genuine Parts HVAC Blower Motors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These HVAC blower motors are electric fans located in the HVAC housing. The fan pushes air through the heater core and evaporator and into the cabin. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Permanently lubricated, self-aligning bearings designed for long life and dependable performance
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
• GM regularly updates production and service part designs to integrate new materials and technologies

As a manufacturer in accumulator/filter driers, we offer quality units produced in a ISO/TS16949 And ISO14001 certified facility. State-of-the-art equipment And high quality materials ensure product integrity for long lasting performance customers rely on.; Our accumulator / filter driers feature quality welds for a durable, leak-free design in addition to high-quality desiccant for appropriate absorption. For easy installation, necessary gaskets, o-rings And seal are included as well.; The accumulator / filter drier acts as a filter by removing moisture And contaminants from the air conditioning system. Such contaminants cannot be removed by flushing, therefore replacing the accumulator / filter drier is essential.; Replacement of the accumulator / filter drier is required to validate compressor warranty And must be replaced anytime the system is serviced.; The absorption of moisture in the system is done through the use of a desiccant bag. A leaking or open system can cause the bag to become saturated within a few hours making the accumulator/filter drier ineffective.

This replacement engine coolant reservoir is manufactured from quality materials to withstand the stresses of underhood heat and engine vibration. It is engineered and manufactured to match the fit and function of the original part.

Product Features:

• Direct replacement – this engine coolant reservoir matches the fit and function of the original part
• Ideal solution – engineered for a seamless installation
• Durable construction – manufactured from quality materials to withstand underhood heat and vibration
• Trustworthy design – backed by 100 years of automotive aftermarket experience

New Goodmark 4 Piece Set Of Radiator Mount Cushions, For Models With 4 Row Radiators

Product Features:

• For Models With 4 Row Radiators
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle