Chevrolet Corvette Distributors

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system or operating system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.

One of the best, and sometimes missed tuning tricks is not to just optimize your initial timing, but to bring in timing advance more quickly than the stock distributor can allow. Bringing timing more quickly than stock can provide substantial increases in both torque and horsepower depending on your combination.This is done by changing the springs under the cap. This kit includes three sets of springs which can be used in different combinations to provide full advance sooner than stock. Use lighter springs to bring the advance more quickly, and heavier springs to bring it in more slowly. Two new weights with nylon bushings are also included as are instructions to help with installation. Springs are color code as follows: Light Springs – Black Medium Springs – Silver Heavy Springs – Gold

Product Features:

• Brings in timing more quickly than stock for more torque and horsepower
• Includes three sets of springs to allow for a wider range of custom tuning
• Instructions included to help with installation

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Fel-Pro Oil Pan SnapUps 8mm bolts
• Designed to hold up the pan and gasket, for one person installation
• Engine$aver Hardware
• Unsurpassed quality you can trust
• Sold in sets of four and are reusable

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Replacement Part (only) for PerTronix Flame Thrower Distributors
• Replacement Part (only) for PerTronix Flame Thrower Distributors

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• Application matched component to ensure the system can be returned to like new condition.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Edelbrock part No. 22737 is a bronze alloy drive gear for use on ProFlo EFI & Max-Fire distributor in small-block & big-block Chevrolet engines.

Our Chevrolet front drive distributors brought the need for a distributor plug. Both are billet aluminum and feature a slip collar to ensure correct installation depth.

Product Features:

• Use On Engines w/Wet Sump Oil System And Front Drive Dist.
• Supplied w/Bronze Gear
• Must Be Used w/An MSD Crank Trigger
• Adj. slip collar mounting flange for engines w/modified deck hts.
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Oversized Polished Steel Shaft w/QPQ Coating

Driveworks offers a line of aftermarket parts and accessories that are commercially acceptable and competitively priced, which provides professional technicians and DIYers with an affordable alternative for repairs.

Product Features:

• Direct-fit OE replacement ensures ease of installation
• Designed to meet OE performance
• As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need
• As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need

Replacement rotor for Chevrolet HEI style distributors.

Product Features:

• For HEI distributors
• Resist carbon tracking
• Low resistance brass
• Max voltage transfer
• Molded from insulated material

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.

Product Features:

• Rolled Edges For Strength
• Ideal For Magnetos
• Ideal For Ignition Distributor

Chrome Finish

Product Features:

• Edelbrock part No. 4802 hold-down distributor clamp is for 4.3L V6, small-block V8 and big-block V8 Chevys. It is constructed of die-cast zinc with a chrome finish. Kit includes stud, nut and a washer.
• Includes stud, nut, & washer

When dressing up your engine, be sure not to miss a single detail. After installing a high-performance TSP distributor, hold it down with a color-matched billet aluminum clamp.

Product Features:

• Material: Aluminum
• Fastener Style: Stud
• Hardware: Included

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: springless; single-lip
• Temperature range: -100 Deg. F to 450 Deg. F / -73 Deg. C to 232 Deg.
• Excellent dry running capabilities
• Low coefficient of friction
• Delivers quality and reliable performance for every type of repair

Marine environments place rigorous demands on every component of the ignition system. The combination of water spray, salt exposure, full throttle acceleration and harsh vibrations all take their toll. The MSD Pro-Billet distributor is the strongest and most accurate distributor you can put in your boat. The housing is CNC-machined from a billet of 6061-T6 aluminum creating a housing with no porosity. Each distributor uses MSD’s race-proven magnetic pickup to trigger the ignition control. Mounted just above the pickup is a mechanical advance assembly that is easy to adjust so you can dial-in an ignition curve to match your boat’s application (except PN 8366). For marine use, the distributor cap is bolted to the aluminum base. There are two flame arrestor holes with brass screens machined into the base of the distributor to prevent ignition of gas fumes that may build up in the engine compartment. A special Weathertight connector is supplied. Underwriter’s laboratory approved.

Product Features:

• For Use In Marine Applications w/Chevy V8 Automotive Engines
• Will not accept a vacuum advance canister
• Supplied w/Bolt Down HEI Style Distributor Cap And Rotor
• Weathertight connectors used for locked and sealed connections
• Must Be Used w/An MSD Ignition Control
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• Nylon pads ensure smooth operation of the advance weights

Distributor

Carquest Premium distributors are built to meet or exceed the original equipment (OE) specifications for each application. Our distributors are built by a manufacturer that meets IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Each distributor is supplied with the cap, rotor and any seals needed for installation. Carquest Premium distributors are 100% new and undergo extensive validation testing to ensure long-lasting ignition performance and reliability.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• 100% new unit with no core charges
• Precision machined shafts result in high speed accuracy and help prevent bearing failures
• Every distributor is tested to ensure reliable and long-lasting performance
• O-rings or gaskets included where applicable
• Precision Engineered ignition modules and plugs ensure proper performance plus precise connection.
• Precision machined and ground shafts assure high speed accuracy and prevent bearing failures.
• Original Equipment Equivalent high voltage ignition coils.
• 100% New Components and fasteners eliminate premature failures.

Distributors

Replacement distributor cap and rotor for Flame-Thrower billet and cast distributors. High dielectric strength cap with male or female brass terminals with premium rotor with brass contact.

Product Features:

• PerTronix D600700 Cap Black and Rotor 8 cylinder Flame-Thrower Billet Distributor
• Replacement distributor cap and rotor for Flame-Thrower billet and cast distributors

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

ACDelco Professional Distributor Cap is a high quality aftermarket replacement component for one or more of the following vehicle systems: cooling, hvac, ignition, starting and charging, body-electrical and lighting, wiper and washer, and/or engine fuel management. This premium aftermarket cap is manufactured to meet or exceed your expectations for fit, form, and function.

Product Features:

• Professional, premium aftermarket replacement
• Provides the performance and dependability you expect from ACDelco
• Manufactured to meet expectations for fit, form, and function

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Replacement distributor cap and rotor for Flame-Thrower billet and cast distributors
• Replacement distributor cap for Flame-Thrower billet and cast distributors.
• High dielectric strength cap
• Replacement premium rotor with brass contact.