from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$530.99

High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability

from

$32.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$206.99

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated

Product Features:

High Output Fuel Flow
Flows 170 gph Free Flow
Shutoff Pressure Pre-Set At 8 PSI
Fuel Pressure Regulator Required Recommend P/N 12-704
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
3/4in.-16 Inlet And Outlet Ports

from

$29.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$115.99

Custom Fit Spark Plug Wire Set

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$141.99

The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required
Downshift At Any Speed
Great For Trailer Towing
For Heavy Loads Driving Downhill

from

$21.79

Mr. Gasket Performance Gaskets are a low density material that conforms well to irregular flange surfaces and has very good crush resistance at high flange pressures. Intended for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit.brbrThis Mr. Gasket Performance Timing Cover Gasket Kit includes the timing cover gasket and water pump gasket for your Gen IV or Gen V Chevy 396,402,427,454 Big Block.

Product Features:

Includes Timing Cover Gasket and Water Pump Gaskets
Won’t shrink or stick and provide an airtight leak proof seal
Engineered specifically for big block Chevys and ideal for high performance and race applications
Ensures optimum torque retention ideal crush resistance and excellent sheer strength using minimal clamp force yet still releases easily

from

$145.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$17.09

Distributor Condenser

from

$369.99

Hurst Indy SSA 3-speed shifter kits are designed to be used on most popular 3-speed transmissions in a wide variety of cars. Applications are determined by transmissions and an exclusive engineered mounting design, for most applications.

Product Features:

Spring Loaded Gate
Short Precise Throws
Chrome Plated Stick
All Components Are Plated
Complete with Shifter Boot and Hardware

from

$391.99

The Edelbrock #4144 Classic Series Valve Covers are designed for Chevy 262-400 V8 1959-86 applications. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. They are made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Small Block Chevy 262-400 1959-86
Tall
Polished Aluminum
Set Of Two

from

$16.49

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

8″ diameter
1970-73, 396-427-454 cu. in.
1967-69, 302 cu. in.
1965-68, 327 cu. in. hi-performance
1970-76, 400 cu. in.
1970-73, 350 cu. in.

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$42.49

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$823.99

The MagnaFlow Street Series Crossmember-Back Performance Exhaust System 15896 brings enhanced engine sound and dyno-proven performance to your muscle car with a healthy helping of our deep, resonant signature exhaust note at Moderate exterior and Mild interior sound levels. Thanks to its durable, corrosion resistant stainless steel design, this exhaust system will handle whatever tarmac you decide to leave your mark on. This performance exhaust kit features a crossmember-back layout designed to replace your exhaust system from the crossmember on back. With its fast-flowing, mandrel bent 2.5in. main piping and 2 Straight-Through mufflers ending in a Dual Split Rear exit that you can enhance with tips of your choosing, your muscle car will be sounding as awesome as it looks. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 15896 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s limited lifetime construction warranty.

Product Features:

Dyno-proven performance
Durable corrosion-resistant stainless steel construction
CNC precision robotic manufacturing techniques

from

$1212.00

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

Long Tube Lengths
Long Transition Collectors
Monstrous Low-Mid Range Torque
Keep Top End Horsepower
Provides Finest Fit
Most Durable Design Available

from

$15.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.

Product Features:

Made from hi-performance 60 KV rated alkyd molding compound.
Cap and rotor kits include nylon rotor hold-down screws.
Flame-Thrower dust covers provide a larger air gap around the coil.

from

$1322.99

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

Cam and lifter kit for Big Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$12.99

This chrome-plated steel push-on breather/oil filler cap fits over your oil filler tube. It has a side fitting for easy PCV hose (positive crankcase ventilation) hook up. Perfect compliment to Mr. Gasket matching chrome oil filler tube, #2066

Product Features:

Chrome plated steel
Fits stock factory oil filler tubes
Features side PCV hook up tube
Includes Rubber Grommet

from

$133.99

This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.