Chevrolet 3B Air Intakes

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.

Product Features:

• Nominally Rated At 170,000 PSI Tensile Strength
• Precision Machined Threads For Secure Engagement, And Would not Rust
• Wide Under Head Flange And Companion Washers Provide Even Load Distribution
• Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
• Facilitates Optimum Sealing Of Gasket Surfaces
• 1″ Long

Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.

Product Features:

• Nominally Rated At 170,000 PSI Tensile Strength
• Precision Machined Threads For Secure Engagement, And Would not Rust
• Wide Under Head Flange And Companion Washers Provide Even Load Distribution
• Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
• Facilitates Optimum Sealing Of Gasket Surfaces

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Validated for fit, form, and function
• Engineered for the sealing repair environment
• Unsurpassed quality you can trust

Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!

Product Features:

• All Aluminum Construction
• No Choke Tower For Unobstructed Airflow
• Air Bleeds Moved Outward Allow Smoother Transition Of Airflow
• Down-Leg Boosters For Improved Fuel Signal
• Contoured Hex Head Squirter Screw For Streamlined Airflow
• Internal Pump Passage On Metering Block w/Tunable Bleed Off
• Built In Drain Plug Provides Easy Access to Empty Bowl
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Window On Both Sides Of Bowl For Fuel Level Adjust

Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!

Product Features:

• All Aluminum Construction
• No Choke Tower For Unobstructed Airflow
• Air Bleeds Moved Outward Allow Smoother Transition Of Airflow
• Down-Leg Boosters For Improved Fuel Signal
• Contoured Hex Head Squirter Screw For Streamlined Airflow
• Internal Pump Passage On Metering Block w/Tunable Bleed Off
• Built In Drain Plug Provides Easy Access to Empty Bowl
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Window On Both Sides Of Bowl For Fuel Level Adjust

The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Man. Choke Cable Hand Controlled For Cold Start Control
• 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
• Power Valve Blow-Out Protection
• 100% Wet-Flow Tested To Assure It Arrives Ready To Run
• Does Not Work w/A.O.D. Transmissions
• Installation/Tuning DVD Incl.

The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to push you to the finish line on Saturday night, the Holley 0-4412 Performance 2BBL is the perfect choice.

Product Features:

• Vibratory Polished For Good Looks
• Man. Choke Cable Hand Controlled For Cold Start Control
• 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
• Power Valve Blow-Out Protection
• 100% Wet-Flow Tested To Assure It Arrives Ready To Run

Street Avenger carburetors are known to bolt on right out of the box and Holley is excited to announce the addition of our new 2bbl Street Avenger models available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations; three vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included 3/8″ fuel line connection so there are no unnecessary trips back to the parts store.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Built In No Trouble Fuel Inlet Filter
• Provides Precise Fuel Control For Low End Torque/Acceleration
• Gen Iv No Trouble Power Valve
• Three Vacuum Ports [1 Pcv/Brake 1 Timed Spark 1 Full]
• Limited Lifetime Warranty Defects In Material/Workmanship
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Competition fuel curves provide safe and reliable horsepower for high performance race engines.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Man. Choke Cable Hand Controlled For Cold Start Control
• 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
• Power Valve Blow-Out Protection
• 100% Wet-Flow Tested To Assure It Arrives Ready To Run

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Product Features:

• Polished Version Of Edelbrock PN[7101]
• Polish is Hand-Buffed for Brilliant Shine
• Based on Performer RPM-Series with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• Designed for 1500 to 6500 RPM Street-Driven Power
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades

Edelbrock part #71373 Pro-Flo XT intake manifold is designed for 1957-86 small-block Chevy V8 applications. The Pro-Flo XT intakes are engineered with a large plenum and long tapered runners to deliver maximum horsepower and broad torque throughout the rp

Product Features:

• 1500-7000 RPM Range
• Single Plane Type-Throttle Body XT Style Flange
• 9 in. Front Height, 9 in. Center Height, 8.2 in. Rear Height
• Black Powder Coated Finish
• Made In The USA

Edelbrock part #5418 C-357-B Triple-Deuce intake manifold is designed for 1955-86 262-400 c.i.d. small-block Chevys, this manifold has a balanced 180-degree firing order port runner arrangement. It contains an exhaust gas heat crossover and offers excelle

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type 6-Pack Style Flange
• 3.77 in. Front Height, 4.35 in. Center Height, 4.88 in. Rear Height
• Satin Finish
• Non-EGR

Edelbrock part No. 27031 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. This Performer EPS intake manifold combines a modern runner design with a front mounted oil fill tube for those who want the vintage look of our Classic valve covers with no breathers. Includes Oil Fill Tube (not installed) and matching push-in breather cap. The Oil Fill Tube and Breather are also available separately as No. 4803. This intake manifold is optimized to deliver superior performance with Edelbrock square-bore Performer Series or Thunder Series AVS carburetors. This small-block Chevy manifold has a runner design that’s “tuned” for peak torque at 3500 rpm on a 350-inch engine and it’s ideal for power from off-idle to 5500 rpm. Dyno tests showed gains of 5 hp and 9 ft.-lbs. of torque over the Edelbrock Performer intake manifold No. 21011 on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft.-lbs. of torque for more performance where you need it most. This manifold offers a polished finish for a brilliant shine and classic look.

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 Deg Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Accepts Late-Model Choke; Waterneck; and HEI
• Accepts A/C And Alternator
• Accepts Exhaust Heated Chokes and Accepts EGR

Product Features:

• Designed for Idle to 5500 RPM
• Manifold has a Balanced 180+ Firing Order
• Contains Exhaust Gas Heat Riser
• Offers Excellent Performance Potential
• Front Oil Filler Tube Boss Included
• Carburetor Center-to-Center Dimensions = 5-1/2 in
• Also Available Polished PN[5419] But Not Fit HEI
• Use Rochester 2GC (small 1-7/16 in bore)

Product Features:

• Based on Performer Series with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg .Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• Fits Both Spread and Square Bore Carburetors
• Also in Polished/PermaStar/EnduraShine Finish

Air gap cooler and denser mixture for more power. Street and high performance compatible. Available in cast, polished and endurashine finish.

Product Features:

• Based on C26 Low Profile with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• 1.625 in. Taller Than Low-Profile PN[5425]
• Also Available In EnduraShine Finish PN[75254]
• Also Available As Complete Kit PN[2025/20254]
• Best When Matched with Edelbrock 500cfm Carburetor
• Use Fuel Line Kit PN[8088/8091]
• Use Progressive Throttle Linkage Kit PN[7094]

Product Features:

• Best for the Ultimate in Street High-Performance
• Designed for 1500 to 6550 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades
• Edelbrock Total Power Package Maximizes Gains
• Also in Polished/PermaStar/EnduraShine Finish

Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type-4150 Style Flange
• 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
• Black Powder Coated Finish
• Non-EGR W/ Oil Fill Tube

Product Features:

• Single Plane with Isolated Plenum
• Square Bore Carburetor Mounting Flange
• Isolated Water cross-over
• Power band: 2500-7500 RPM
• Height: Front 4.18″, Rear 5.28″
• Port Size: 1.92″ height 1.20″ width