Cadillac Performance Ignition Products

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-31
• MSD 8225

The updated Fuel Pump Booster is an easy way to maintain the proper fuel pressure on your car after adding a power adder such as a turbo or supercharger. The new model allows you to make your boost adjustments through a PC for improved control and accuracy. The Booster ensures that the engine receives the fuel it needs to make up for the increase in air being pumped into the intake manifold. It will increase the voltage to the factory fuel pump in proportion to manifold boost pressure in order to maintain the proper fuel delivery. The amount of increase is adjustable from a range of an additional 1.5 -22 volts up to 30 psi which can all be set and adjusted from your PC with MSD’s easy to use Windows based software. The MSD Booster will wire to the factory fuel pump relay or with a secondary booster pump.

Product Features:

• Direct performance replacement
• For GM 2 Tower Coils Used From Mid 1980s To Late 1990s
• 80:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions
• CARB E.O. Approved

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

• Direct performance replacement for GM dual connector coil
• 100:1 Turns Ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Similar to Standard Motor Products SMP Dr-32
• Long Life And Great Looks

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

• Improved output coil for electronic ignitions
• Works w/Blaster Ignition Or MSD 5/6/7 Series
• Ballast Resistor Required If Used w/Stock Points Ignition
• Alkyd tower w/high dielectric properties lessens carbon tracking

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

• Replacement Coil For GM Dual Connector Coil
• Improved Turns Ratio
• Lower Primary Resistance
• Bolt-In replacement coil
• Produce More Output Voltage
• Smooth Idle

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP DR-37
• MSD 8226
• Resist Corrosion
• W/New Mounting Hardware

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• More Accurate Ignition Timing
• Improves Performance And Fuel Economy
• Provides More Accurate Ignition Timing
• Easy To Install w/Hand Tools
• Reduced Maintenance
• Thermal Clad Based Surface Mount Construction
• Utilizes Specialized Electronic Circuitry
• Ignition Timing Is Stable From 1 To 10000rpm

This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM Remote Mount Coil HEI distributors for V8 engines.

Product Features:

• Fits Most Stock And Modified Distributors
• Solid State Electronics
• Dwell Control Circuit

When it comes to late model performance parts, nothing beats bolt-on and direct connection components. These new bolt-in coils are designed with improved materials and windings to produce a stronger output. GM single connector coil PN 8231. Used on 1996 to 1999 General Motors vehicles. Installation tip: if you plan to install an MSD Ignition with this coil, use a PN 8877 harness for a direct plug-in installation.

Product Features:

• Direct performance replacement coil for GM 1996-1999
• 80:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

• Extra Thick Contact Arms
• Large Radius Tungsten Contacts
• High Strength Phenolic Rubbing Blocks
• Prevents Points Float
• Moisture-Proof Buna-N Condenser

These ACCEL Super Stock wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with zinc-plated steel terminals.

Product Features:

• Graphite supression eliminates RFI/EMI
• 3,000 to 7,000 ohms per foot of resistance
• Silicone Spark Plug Boots
• 450 Degree Temperature Rating

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

• Glass Filled Polyester Case
• Longer Spark Duration
• Increased Performance
• No Energy Loss Due To Arcing
• Includes Brass Contact Terminal

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

MSD Ignition multiple spark coils (MSC) will fit in place of the stock Gen-III GM coils and connect directly to the factory connectors. Once installed, you’ll have the power and performance of higher energy sparks, crowned with MSD’s multiple spark discharge. Increased spark energy and voltage, along with multiple spark capabilities, help improve the combustion process of the fuel mixture to create an efficient burn. This results in improved throttle response, smooth idle and quick starts, plus increased high RPM performance! The MSC delivers up to three times the current of the stock coils. Plus, the coils fire multiple times!

Product Features:

• Produces multiple; powerful sparks
• Two connectors molded into custom housing
• Improved performance
• Produces three times the spark current of stock
• Complete kit with mounting hardware
• Easy installation
• CARB approved legal for use in all states
• OBD II approved legal for use in all states

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

• Externally mounted coil
• Increases reliability
• Increase performance
• High quality plastic
• Resist spark loss
• Use brass conductors
• Low resistance connections
• No modifications

Distributor Condenser