Cadillac CTS Performance and Racing Products

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

This 7° steel retainer for GM Gen III applications with #26915 or #26918 Beehive Valve Springs is precision machined from 4140 chromemoly steel and finished in black oxide. This precision retainer is specifically designed for positive location when combined with COMP Cams high-quality valve springs.

Product Features:

• 7° angle retainers for 1.055″ diameter valve springs, stock diameter valve stems
• O.D. – 1.030″, Step 1 – .640″
• Precision machined from 4140 chromemoly steel and finished in black oxide
• Designed for positive location when combined with COMP Cams high-quality valve springs

Trinity 2

MSD Ignition multiple spark coils (MSC) will fit in place of the stock Gen-III GM coils and connect directly to the factory connectors. Once installed, you’ll have the power and performance of higher energy sparks, crowned with MSD’s multiple spark discharge. Increased spark energy and voltage, along with multiple spark capabilities, help improve the combustion process of the fuel mixture to create an efficient burn. This results in improved throttle response, smooth idle and quick starts, plus increased high RPM performance! The MSC delivers up to three times the current of the stock coils. Plus, the coils fire multiple times!

Product Features:

• Produces multiple; powerful sparks
• Two connectors molded into custom housing
• Improved performance
• Produces three times the spark current of stock
• Complete kit with mounting hardware
• Easy installation
• CARB approved legal for use in all states
• OBD II approved legal for use in all states

Knowing your coolant temperature can help to prevent burn injuries. Thermocap Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermocap Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree F temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges.

Product Features:

• Indicates Coolant Temperature
• Helps to Prevent Injuries from coolant or steam burns
• Integrated Coolant Reclamation Valve
• Improves Underhood Appearance
• Fahrenheit and centigrade readings
• Various valve pressures available

A custom computer designed roto-molded housing eliminates the use of multiple components and ensures the coolest air intake charge available. A clear sight window allows for filter inspection without removal of the airbox. The roto-molded housing is made out of black cross-linked polyethylene. The housing is designed to retain the same water fording height as the factory intake system while providing more air flow and better protection. This System uses a CAD designed, dyno-tuned, roto-molded intake tube to achieve maximum power gains while maintaining a perfect fit. This tube has built-in resonance chambers to catch un-wanted air intake noises. This Momentum GT intake system was designed around the largest filter possible to allow maximum performance and filtration. This filter has a massive 5″ round flange and is 8″ tall with an inverted top and features our pre-oiled Pro 5R media. The Pro 5R performance air filter features 5-layers of progressively finer mesh cotton media providing maximum airflow and performance. The unique air filter to housing interface (patent pending) allows for maximum filter size which increases the available air volume while simplifying the installation process. Premium stainless steel T-bolt clamps are used for durability and provide the best corrosion resistance possible. Momentum GT intakes are designed with fewer parts for a quick and simple installation

Product Features:

• Pro 5R Filter Media
• 5-Layer Progressive Cotton Gauze Media
• Washable And Reusable Air Filter
• Rotomolded Tube

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

Designed to take advantage of the GM LS engine’s larger camshaft journal diameter, the XFI RPM camshaft line takes Xtreme Energy technology to deliver excellent power.

Product Features:

• Designed with Xtreme Energy technology to provide excellent power with the LS engine’s enhanced cylinder head design and high RPM potential.
• Takes advantage of the LS engine’s larger journal diameter, base circle and 1.7+ rocker arm ratio.
• Provides outstanding low RPM torque with increased stability.

Edelbrock #8895 Water Pump GM gen III ls1 & gen iv ls engines insert style ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “supe

Product Features:

• Standard Impeller Rotation
• 0.750 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 6.00 in. Block To Hub Height
• Natural Finish

COMP Cams GM LS Series RPM Valve Train Upgrade Kits replace stock valve train components for more usable horsepower and a higher rpm operating range. This kit includes Hi-Tech Pushrods, Beehive Valve Springs and Titanium Retainers.

Product Features:

• For GM LS series applications
• includes Hi-Tech Pushrods, Beehive Valve Springs and Titanium Retainers
• Replaces stock valve train components for more usable horsepower and higher rpm range

Product Features:

• This dry single stage plate sandwiches between the bottom base and top plate on Holley Hi-Ram intake manifolds
• Designed specifically for optimum nitrous distribution on LS-based engines
• Sprays nitrous directly into each cylinder runner for proper nitrous distribution
• Features a machined 0.103″ passage that feeds eight 0.040″ openings per intake runner
• Plate is made from billet 6061-T6 aluminum and has laser etched NOS logo
• Anodized Black for corrosion resistance and high quality appearance
• Includes jetting for 50, 100, 150, 200, and 250 horsepower configurations
• Supports up to 1000+ horsepower (jets purchased separately)
• Includes Plate, Gasket, Hardware, Jet Holders, and Jetting for up to 250 horsepower

LS Cast Iron Exhaust Manifold

Designed to open at 160 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:

• Opens sooner than stock at 160 degrees
• High flow design for performance applications
• Includes rubber o-ring seal/gasket
• Incorporates pressure relief valve

Product Features:

• The Holley GM LS1/LS2/LS6 2x4V dual-plane was designed in the tradition of the great dual Holley 4160 induction systems that competed on drag strips, in Trans-Am and at Lemans in the 1960’s.
• The dual-plane equal-distribution layout produces great mid-range torque without compromising top end power.
• Carbureted and EFI versions available
• Power band from 1500-7000 rpm
• Appropriate for any street/performance, muscle car, or street rod enthusiast
• Cast aluminum construction
• Intended for use on all GM LS Gen III engines equipped with LS1/LS2 style cathedral port cylinder heads
• Carb Flange Center-To-Center: 8-5/8″

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N’s Limited Warranty.

Product Features:

Product Features:
• Designed to allow high flow rates and a consistent flow of oil to your engine
• Pleated synthetic-blend filtration media removes most harmful contaminants
• Fast and easy Wrench-Off removal using the welded one-inch hex nut
• High capacity to withstand the service intervals recommended by vehicle manufacturers
• Heavy-duty canister for outstanding durability
• Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
• Designed to operate with all synthetic, conventional, and blended motor oils
• Limited Warranty

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.

Product Features:

• Guaranteed to increase horsepower and torque.
• Mandrel-bent aluminum intake tube paired with oversized oiled cotton air filter.
• Engineered to provide high airflow and exceptional filtration.
• Replaces factory air filter and intake tube.
• Filter only requires cleaning every 100,000 miles under normal highway driving conditions.
• Typical installation can be completed in 60 minutes or less with simple hand tools.
• No-Hassle Lifetime Limited Warranty.
• Will not void vehicle warranty(limited)

Edelbrock part #7343 RPM-Link adjustable true-roller timing chain Set now, you can dial-in your camshaft with ease with our RPM-Link Roller Timing Chain Set. RPM-Link timing chain bolt onto your engine just like any other timing chain set, so there’s no m

Product Features:

• Keyway Adjustable
• Single Roller Timing Chain Type
• Induction Hardened Billet Steel Material
• No Machining Required
• No Special Offset Bushings Needed For Installation

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Product Features:

• Fits GM LS engines with drive-by-wire style 90mm or 92mm throttle body
• Includes jetting for 100, 125, & 150 horsepower
• Fits Holley and Sniper EFI , or MSD Atomic intake manifolds
• This wet kit provides exceptionally smooth power delivery
• Single 90mm ╜ inch thick black plate between the throttle body and manifold
• Bottle is made from 6061-T6 Aluminum
• Supports up to 250 RWHP (jets purchased separately)
• Includes a 10 lb. black nitrous bottle with brackets