Buick Electra Performance Engines

“Edelbrock Performer-Plus Camshaft No: 2152 is designed for 400-425-455 Oldsmobile V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2152 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 445 Ft Lbs of Torque when paired with Performer Olds 455 intake manifold No: 2151 and stock cylinder heads. Will not fit Tornados or 1966 and earlier. Fits 1967-84 400-425-455, 39 Degree bank angle engine. Camshaft specifications: – Intake duration: 214 Degrees – Exhaust duration: 224 Degrees – Intake lift: .472″” – Exhaust lift: .496″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 15″””

The Tork Master 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1996 4L60E w/30 spline input transmissions. This converter retains the lock-up feature. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75 in. bolt circle

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Edelbrock part No: 7829 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

“Competition Cams Magnum 8.280″” Long, .080″” Wall, 3/8″” Diameter Pushrod Set of 8, 7131-8. ”

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

“Competition Cams Valve Spring, 1.384″” 2 Spring, 988-1. ”

The Edelbrock No: 5792 Sure Seat Valve Spring for Chrysler 383-400-413-440 V8 1969-79 O.E Cast iron cylinder heads are made of highest quality spring wire and precision wound to close tolerances, our Sure Seat Valve Spring sets are for use on original equipment heads when installing Edelbrock Performer-Plus, Performer RPM and Torker-Plus camshafts. These are the same high-performance springs used on Edelbrock Performer and RPM cylinder heads. For camshaft warranty compliance, use only the springs recommended by Edelbrock for each camshaft application.

Edelbrock Water Pump Cartridge for Small-Block Chevy (Race Style), 8827.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Competition Cams High Energy Timing Set for ’62-’77 B.O.P. 198-231 V6, 3215.

Edelbrock RPM Air-Gap Oldsmobile 455 Intake Manifold, 7551.

Edelbrock Performer Small Block Oldsmobile 350 Intake Manifold, 7111.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions