1988 Buick Electra Performance Engines

“Competition Cams Magnum 8.280″” Long, .080″” Wall, 3/8″” Diameter Pushrod Set of 8, 7131-8. ”

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

“Edelbrock part No: 7346 head gasket is intended for 400-455 C.I.D. Buick V8 engines. This gasket comes as a set and has a 4.400″” bore size, .050″” compressed thickness and 12.5 cc volume.”

“Edelbrock part No: 3712 Performer-Plus camshaft is designed for small-block Oldsmobile 350-403 V-8 applications. This Edelbrock cam kit produced 330 ft-lbs. of torque when used with No: 3711 intake and stock iron cylinder heads on a 350 engine. The camshaft will produce optimum torque from the low-end to the mid-range, Performer-Plus camshafts match with Performer manifolds for vehicles operating from off-idle to 5500 rpm. This Performer-Plus is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. All camshafts include flat tappet lifters, assembly lube and instructions. Camshaft Specifications: – Duration at .050 Intake: 204 degrees – Duration at .050 Exhaust: 214 degrees – Lift at Valve Intake: .449″” – Lift at Valve Exhaust: .473″” – Lobe Separation: 114 Degrees – Intake Centerline: 106 Degrees – Idle Vacuum at 1000 RPM’s: 16″””

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Edelbrock part No: 7829 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

The Tork Master 2400 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1996 4L60E w/30 spline input transmissions. This converter retains the lock-up feature. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75 in. bolt circle

B&M Nitrous HoleShot 3600 stall for 1965-91 TH400, 425 and 1968-81 TH350, 375 (Not TH350C) transmissions is an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Nitrous Holeshot converters feature furnace brazed impeller and turbine, new precision steel alloy pump drive tube, new heavy duty needle bearings between the stator and impeller (not a thrust washer) and needle bearings between the stator and turbine. Other features include dual pattern 10.75 and 11.50-inch bolt circle, a new turbine hub, new springs and rollers in the stator and anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower that a nitrous plate system delivers. Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. These are serious converters for serious performance street cars. To prevent contamination left from worn parts being circulated in your new components causing premature wear, we strongly recommend protecting your investment by adding a B&M transmission cooler with all new transmission installations. Listed converters are NOT to be used in trans-brake applications. Not for use in trans-brake applications.

This Holeshot 3000 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C). Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Has both 10.75 and 11.50-inch bolt circles.

The Tork Master 3000 fits 1965-91 GM TH400, 425, 375 and 1968-81 GM TH350, 375B (not 350C) transmissions. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

This Holeshot 2000 fits 1984-93 GM 700R4/4L60 w/30 spline input, 1993-1997 4L60E w/30 spline input, and 1997-04 Corvettes. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace-brazed impeller fins and turbine, a new precision alloy impeller hub, and new heavy-duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate-type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, and less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide, or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Competition Cams Cam & Lifter Kit, Oldsmobile V8 280 Magnum Hydraulic 1 Ea, CL42-231-4.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

“Edelbrock Performer-Plus Camshaft No: 2152 is designed for 400-425-455 Oldsmobile V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2152 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 445 Ft Lbs of Torque when paired with Performer Olds 455 intake manifold No: 2151 and stock cylinder heads. Will not fit Tornados or 1966 and earlier. Fits 1967-84 400-425-455, 39 Degree bank angle engine. Camshaft specifications: – Intake duration: 214 Degrees – Exhaust duration: 224 Degrees – Intake lift: .472″” – Exhaust lift: .496″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 15″””

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.