Buick Century Air Intakes
Top Buick Century Air Intakes Categories
We carry over 263 Air Intakes in inventory for the Buick Century. If you’re looking for aftermarket Air Intakes for your Buick Century, check out all these categories:
Essential Buick Century Air Intakes
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90562)
from
$74.99
Product Features:
See More
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES – Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE – Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Carquest – Air Charge Temperature Sensor (Part No.31A1016)
from
$28.99
The Air Charge Temperature Sensor provides an input to the vehicles computer as to the temperature of the air entering the engine via the air cleaner assembly. The engine computer uses this input to control many operating conditions which in turn provides optimal engine operation, engine performance and clean tailpipe emissions.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
- Application matched components ensures system operation in like new condition.
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$196.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Carquest Premium – Multi-Purpose Relay (Part No.RAA1266)
from
$20.99
Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
- Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
Felpro – Carburetor Mounting Gasket (Part No.60248)
from
$7.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
GM Genuine Parts – Fuel Injection Throttle Body Gasket Kit with Seals, Gaskets, and Diaphragm (Part No.40-707)
from
$122.99
GM Genuine Parts Fuel Injection Throttle Body Repair Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1013)
from
$31.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Performer Air-Gap Intake Manifold for 1955-86 Small-Block Chevy (Part No.2601)
from
$395.99Product Features:
- Based on Performer Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg .Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- Fits Both Spread and Square Bore Carburetors
- Also in Polished/PermaStar/EnduraShine Finish
United Carb – Remanufactured Carburetor 2 Barrel (Part No.1-330)
from
$360.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Dorman – Rivet-Push In-Hole Diameter .250 In. (Part No.799-110)
from
$5.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$36.99
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Felpro – Carburetor Heat Shield Gasket (Part No.60731)
from
$7.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Carquest – Carburetor Choke Thermostat (Part No.779-1485)
from
$69.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More
Dorman – Rivet-Push In-Hole Diameter .500 In-Head Diameter 1 In-Length .900 In (Part No.45813)
from
$1.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Dorman – Nylon Nut – 1/4 In. (No.14) (Part No.961-351D)
from
$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Buick Century Air Intakes Categories
Helping You Find the Right Air Intakes for Your Buick Century
You love your Century. So we’ve made it easier than ever to help you find Buick Century Air Intakes in our online catalog. Our inventory holds 263 aftermarket and OEM Air Intakes for your Buick Century, ranging from $1.99 to $1,949.99.
We offer parts from 16 brands trusted to make quality Air Intakes for your Buick Century. Before you buy, take some time to read through customer reviews. We currently have 14,214 reviews of Buick Century Air Intakes from previous customers. Some of the top rated parts include Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet with 4.7 stars and Engine Intake Manifold Gasket Set with 4.6 stars.
Find your Century Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Buick Century part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Buick Century
Our inventory holds Air Intakes for your Buick Century from 16 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Dorman, all of which can keep that Buick happy.
We have Delphi parts available for your Buick Century in categories like Throttle Bodies & Carb Parts. Some of the top-rated Delphi parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your Buick Century across several catalog categories, including Intake Manifold Parts. Some of our most reviewed Felpro parts include:
FAQs for Buick Century Air Intakes
What are the most purchased Air Intakes for the Buick Century?
Out of 263 Air Intakes for the Buick Century, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
What are the top-rated Buick Century Air Intakes?
Top-rated Air Intakes for your Buick Century based on customer reviews/ratings are:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
“Easy bolt on installation”
