Bristol 411 Air Intakes
Top Bristol 411 Air Intakes Categories
We carry over 100 Air Intakes in inventory for the Bristol 411. If you’re looking for aftermarket Air Intakes for your Bristol 411, check out all these categories:
Essential Bristol 411 Air Intakes
Holley – Carburetor – 750 CFM Street Hp Mech Sec (Part No.0-82751)
from
$799.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Calibration For Outstanding Drivability
- Contoured Venturi Inlet Balances Airflow For Increased hp
- Screw In Air Bleeds For Precision Tuning Capabilities
- Four Corner Idle For Precise Idle Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Intended For Lightweight Vehicles w/Man/Auto Trans
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Felpro – Valley Pan Gasket Set (Part No.MS 96007)
from
$32.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- RIGHT TYPE – Valve stem seals designs are application-specific for the repair occasion using either deflector (umbrella) seals, O-ring style or positive seals
- QUALITY MATERIALS – Each valve stem seal features materials based on the specific application for your vehicle repair
- ENGINEERING EXPERTISE – Parts are reviewed, validated and approved by Fel-Pro engineers through rigorous research, development and testing
- INSTALLATION AID – Installation tool included to protect inner lip of seal from damage during seal installation
- COVERAGE – Available for domestic and foreign nameplate vehicles
Felpro – Carburetor Mounting Gasket (Part No.60159)
from
$5.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$17.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$60.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$47.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Bristol 411 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Bristol 411
You love your 411. So we’ve made it easier than ever to help you find Bristol 411 Air Intakes in our online catalog. Our inventory holds 100 aftermarket and OEM Air Intakes for your Bristol 411, ranging from $4.29 to $1,949.99.
We offer parts from 3 brands trusted to make quality Air Intakes for your Bristol 411. Before you buy, take some time to read through customer reviews. We currently have 420 reviews of Bristol 411 Air Intakes from previous customers. Some of the top rated parts include Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Street Carbs with 3.4 stars.
Find your 411 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Bristol 411 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Bristol 411
Our inventory holds Air Intakes for your Bristol 411 from 3 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Holley, all of which can keep that Bristol happy.
We have Felpro parts available for your Bristol 411 in categories like Intake Manifold Parts and Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
FAQs for Bristol 411 Air Intakes
What are the most purchased Air Intakes for the Bristol 411?
Out of 100 Air Intakes for the Bristol 411, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
from
$60.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated Bristol 411 Air Intakes?
Top-rated Air Intakes for your Bristol 411 based on customer reviews/ratings are:
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
from
$26.99
(6)
Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs
“Holding up well so far”
