Bricklin SV-1 Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

“Edelbrock part No: 7182 Performer RPM Camshaft is designed for Ford 351W V-8 applications. This Edelbrock cam kit produced 400 HP & 412 ft-lbs. of torque when used with No: 7181 intake and No: 60259 cylinder heads on a 351W engine. The camshaft works well with high-performance’s street applications, Performer RPM cams provide power from 1500 to 6500 rpm. This hydraulic lifter camshaft is dyno-matched to Performer RPM manifolds for high-rpm horsepower while still maintaining acceptable low-end torque. With 10 to 12 inches of manifold vacuum at idle, Performer RPM cams have more lift and duration than most street camshafts. Hydraulic flat tappet lifters are included with each Performer RPM camshaft. Camshaft Specifications: – Duration at .050 Intake: 234 degrees – Duration at .050 Exhaust: 244 degrees – Lift at Valve Intake: .496″” – Lift at Valve Exhaust: .520″” – Lobe Separation: 110 Degrees – Intake Centerline: 106 Degrees – Idle Vacuum at 1000 RPM’s: 11″””

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

The Edelbrock No: 5792 Sure Seat Valve Spring for Chrysler 383-400-413-440 V8 1969-79 O.E Cast iron cylinder heads are made of highest quality spring wire and precision wound to close tolerances, our Sure Seat Valve Spring sets are for use on original equipment heads when installing Edelbrock Performer-Plus, Performer RPM and Torker-Plus camshafts. These are the same high-performance springs used on Edelbrock Performer and RPM cylinder heads. For camshaft warranty compliance, use only the springs recommended by Edelbrock for each camshaft application.

Competition Cams High Energy Timing Set for ’69-’81 AMC 290-401 V8, 3218.

For circle track and endurance racing engines. Black anodized finish with 0.10 inch thicker rear cover. Impeller is larger than others for max pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of black with in 1 piece. Only flows in one-direction for optimum efficiency.

The Edelbrock No. 5028 E-Series Cylinder heads are designed for Small-Block Ford applications. The Edelbrock E-Series cylinder heads are a step up in affordable performance from our E-Street line. They feature larger runners for increased airflow, revised exhaust ports and larger diameter springs for higher lift camshafts, making them ideal for a spec series racer and larger displacement engines. The Edelbrock No. 5028 E-Street Cylinder heads also have as-cast ports and maintain the stock exhaust port location, making them compatible with OEM headers and hardware.

Holley EFI MFLD KIT FORD 351W HI-RAM 95MM EFI, 300-241.

Holley EFI KIT FORD 351W HI-RAM 95MM EFI BLACK, 300-241BK.

Edelbrock Performer 351-W Intake Manifold for S/B Ford 351 Windsor, 2181.

Edelbrock part #7581 RPM Air-Gap 351W intake manifold is designed for street and high performance 351-427 c.i.d. 351W Ford V8 applications. The RPM Air-Gap incorporates the same race-winning design that’s been used on our Victor Series competition intakes for decades. The Air-Gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power. Larger cross sectional area and a taller carb flange than #7181 for compatibility with large displacement, stroker 351W based engines. Includes bosses for nitrous and rear water crossover. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions