BMW 850CSi Brake Parts

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Prevents noise and premature wear
• Provides longer brake life and performance

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

• Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
• Tensile minimum load holds up to 1800 N
• All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
• Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
• Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
• Brand may vary by location

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

The Brembo brand has a range of over 1,600 items, which covers a remarkable 98% of all passenger cars and commercial vehicles on the roads in Europe today. Brembo manufactures an OE-Quality Brake Disc that assures maximum performance and enhanced driving comfort and offers with its aftermarket rotors the same levels of quality, technology and performance that are found in many of the prestigious OEM fitments. Brembo UV Coating Technology : Environmentally friendly, solvent free UV coating offers superior protection of the disc, including braking plate surfaces. Includes new intelligent marking location for immediate control of the minimum thickness. High Carbon Discs: With their optimized thermal inertia, Brembo High Carbon discs reduce both vibration and noise. These products are the result of Brembo technology and a meticulously controlled production process in the brands foundries, which makes it possible to precisely vary the chemical composition of the cast iron, increasing the percentage of carbon in High Carbon discs. PVT pillar venting technology: ( Vented Rotors Only ) Brembo PVT discs feature the exclusive pillar venting system patented by Brembo, which improves cooling capacity and increases resistance to thermal cracking by over 40%. Fixing screw kits: discs are supplied with all the necessary fixing hardware for simpler, more efficient and safer installation

Product Features:

• Metallic finish that maintains a clean and bright appearance over the entire life span of the disc
• Protective coating on braking plate surfaces, external diameter and disc hub to ensure complete protection
• New location for minimum thickness control with greater ease of reading for service professionals
• Water-based paint free of chemical solvents – Energy efficient UV coating process
• Superior to products currently on the market proven by resistance to: Salt spray testing, Humidity and High temperatures BREMBO UV COATED DISCS BROCHURE

Nut

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on side of brake pressure regulator. Fine thread pitch.

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
• Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Bowa electronic brake pad wear sensors are engineered and manufactured to original equipment specifications and are designed to withstand the extreme heat generated by the brake pads. The engineers at Bowa make certain that all materials, parts and tolerances meet the same high standards as the OE brake sensors they supply to brake manufacturers and auto makers worldwide.

Product Features:

• Exact Replacement with OE Fittings and Connectors
• Highly Durable and Resistant to Temperatures
• Supplied with OE style electrical connectors
• Bowa is an OE supplier to Brake and Vehicle Manufacturers

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

• Industry-leading number of application specific formulations for maximum performance and extended pad life
• On-vehicle testing similar to original equipment tests
• Patented 4-Layer HEX Shim Technology provides quiet braking
• HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
• Burnishing compound allows for a faster break-in of pads and rotors
• PTFE coated hardware and caliper pin grease included for nearly every application
• Wear sensors included on most European applications that require replacement
• Powder-coated backing plate prevents corrosion

The TRW Premium brake pads are designed and manufacturing to original equipment specifications, assuring superior quality and fit. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

• OE-Equivalent and Direct Fit application.
• Include the OE specified shims.
• Low noise and reduced vibrations.
• Formulated to OE Specifications.
• Superior friction qualities.
• Organic blended compound.

The ATE Caliper Guide Pin Cover is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

WBR Run True Technology Metallurgic-Gray (MG) Finished Rotors All World Brake Resources (WBR) brake rotors with Run-True technology are manufactured to match the exact OE fit, OE construction, and precision finishing to ensure quick and easy installation, as well as trouble-free functionality for the life of the rotor. The Metallurgic-Gray coating is applied to all outward non-friction surfaces including in the gap between the plates covering the cooling vanes and cured through an oven drying process. The Gray coating provides an effective anti-rust protection to help maintain a clean appearance. The coating used for WBR is also similar to the OE color used by many OE car makes. WBR Brake Rotors with Run-True Technology have ultra tight tolerances that provide the finest braking experience, from break in throughout the life of the rotor, reducing the chance of warping even under extreme braking temperatures. The coated brake disc provides a protective water based coating that prevents rust and corrosion, extended rotor life and improved visual appearance. WBR Brake Rotors are manufactured to meet or exceed the original equipment manufacturer specification for durability, fit, and function.

Product Features:

• High metallurgical and machining standard to improve stopping distances
• Produced to match OE design fitment – G 3000 gray iron
• Mill balanced
• TS16949 certified
• Non-directional finish provides smooth vibration free performance
• No need for machining prior to installation
• Durable Metallurgic-Gray finish to all outward non-friction surfaces
• Metallurgic-Gray anti-rust protection to help maintain a clean appearance
• Compatible with NAO, Ceramic and Semi-Met pad compounds for reduced noise
• Designed to minimize brake fade and extend pad and rotor life
• 24/24 Warranty – limited warranty against defects in material and workmanship Technical Service Bulletins

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Coat-Z protective anti-corrosion coating
• No formation of rust at the hub and herewith improved visual appearance
• Immediate functional capability without removal of the coating before mounting
• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

The Brembo brand has a range of over 1,600 items, which covers a remarkable 98% of all passenger cars and commercial vehicles on the roads in Europe today. Brembo manufactures an OE-Quality Brake Disc that assures maximum performance and enhanced driving comfort and offers with its aftermarket rotors the same levels of quality, technology and performance that are found in many of the prestigious OEM fitments. PVT pillar venting technology: (Vented Rotors Only) Brembo PVT discs feature the exclusive pillar venting system patented by Brembo, which improves cooling capacity and increases resistance to thermal cracking by over 40%. Fixing screw kits: discs are supplied with all the necessary fixing hardware for simpler, more efficient and safer installation

Product Features:

• OE-Equivalent and a direct fit replacement
• Made of special cast iron with high carbon content
• Pillar Venting Technology (Vented Rotors Only)
• Easy Check wear indicator system
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Exact fitment and original replacement
• Helps deliver a quieter, more efficient braking system
• Low-friction PTFE coating to reduce drag
• Manufactured with quality materials to suppress high stress levels

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Increases the life span of the brake pads
• Restores brakes to like-new performance
• Prevents noise and premature wear
• Direct replacement for a proper fit