from

$29.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$26.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$192.36

Heater Valve

from

$434.25

Radiator

from

$159.99

Carquest Premium Blower Motors are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile A/C experience, fix it once and fix it right with Carquest Premium Blower Motors. Meets or exceeds OE design. Magnetic size and properties compare or exceed OEM. Windings meet or exceed OEM Specifications. Motor RPM equivalent to or exceeds OEM motor.

Product Features:

Meets or exceeds OE design and performance
Magnetic size and properties compare or exceed OEM
Windings meet or exceed OEM specifications
Motor RPM equivalent to or exceeds OEM motor

from

$1.97

ACM is a supplier of Original Equipment quality climate control products.

from

$479.99

Carquest New Compressors are designed, manufactured and tested to meet or exceed strict original equipment specifications for superior quality and performance. Each new compressor is tested to provide durable life to the vehicle’s air conditioning system. All new compressor components are assembled using state of the art equipment and techniques to ensure smooth operation. Each part is equipped with a clutch and connector that matches the original equipment part and provides an exact replacement to your vehicle’s part. All compressors are supplied with the necessary gaskets and o-rings for installation.

Product Features:

Each new compressor design undergoes rigorous life cycle testing at high RPMs and pressures to ensure that they can withstand years in the harshest conditions.
New compressors are designed with utmost precision using 3D coordinate measuring machines to ensure a perfect fit.
The production process contains automated controls at every stage that alerts and halts production in case of an error, assuring that the finished product will always be flawless.
All new compressors must pass a helium leak test and pump up function test prior to packaging.
O-Rings and gaskets necessary for installation are included.

from

$223.51

Like all DENSO First Time Fit® A/C components, our condensers are designed and manufactured to integrate seamlessly with the vehicle’s original air conditioning system. DENSO condensers match up to OE condensers at every benchmark. Multiflow, subcooling, and the latest Ssrpentine condenser styles are offered to provide the optimum configuration for each application. Premium aluminum construction improves reliability, resisting corrosion to avoid expensive system leaks, while the superior fin wave design offers higher heat transfer and maximum refrigerant condensation. Heat exchanger cores are specially designed to shed airborne material buildup, allowing the A/C system to operate at peak efficiency with minimal maintenance, assuring years of trouble-free service.

Product Features:

Zinc diffusion layer improves corrosion resistance
Unique fin design to minimize airflow blockage
High performance design reduces the required compressor power
System Efficiency: Superior fin waves provide a higher heat transfer coefficient and full condensation.
Engineered to Perfection: OE quality engineered for unparalleled performance
Exact Fit: Condensers install with speed and ease
Reduces required compressor power, resulting improved fuel economy
Restores A/C performance to as-new condition
First Time Fit® assures bolt-in replacement; no brackets or adapters
Greater Durability: Pure aluminum construction provides greater resistance for corrosion

from

$35.49

Carquest Expansion Valves are designed to regulate the flow of refrigerant through the air conditioning system to provide optimal cooling to the passenger compartment. Each expansion valve is manufactured to original equipment specifications to perform its function even in the harshest climates. Each part is supplied with the necessary gaskets and o-rings for installation.

Product Features:

The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
O-Rings necessary for installation are included.

from

$834.45

Water Pipe

from

$57.48

Oil Temperature Send

from

$79.13

A.P.A. URO is a supplier to many automotive manufacturers and provides OE quality European replacement parts to the aftermarket. URO Parts is a highly diversified product line including, body rubber, electrical, suspension, steering, cooling and air conditioning components. Seal Kit for Repair Kit 11 14 1 439 975R

from

$79.99

Rein Automotive OE quality expansion tanks, install, fit and perform the way the original manufacturer intended. These tanks are designed to match or exceed the OE materials used and are produced from virgin plastic with no regrind to prevent cracking from heat cycles and ensure the plastic is durable and will have a long service life.

Product Features:

Produced from virgin plastic meeting/exceeding OE specifications and ensuring long life
Resistant to cracking and wear from heat cycles preventing coolant loss
Direct fitment allows easy installation
Manufactured to strict engineering standards/specifications in materials and tolerances

from

$125.59

AT Oil Cooler Thermo

from

$13.67

Water Pump Plug

from

$45.99

Water Pump Pulley

from

$29.68

A/C Pressure Switch

from

$18.99

New Standard Replacement A/C System Seal Kit, MT2640, L4 Engine

Product Features:

MT2640, L4 Engine
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$112.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$79.67

Drier Desiccant Elem

from

$3.49

MAHLE gaskets provide world class sealing products trusted by OEMs & Technicians around the globe.

Product Features:

All MAHLE gaskets meet or exceed the original equipment specifications providing the finest sealing products available
MAHLE gaskets utilizes OE equivalent or better materials in all our gaskets
MAHLE gaskets is the leader in Domestic, Asian and European applications
The contents of MAHLE gaskets are packaged in shrink wrapped tray, giving you the added security of knowing that you have the right parts, prior to opening the package

from

$162.94

Blower Motor Regulat

from

$14.47

Radiator Mount

from

$4.99

This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:

Ideal replacement – this engine coolant bleeder screw matches fit and function of the original equipment screw
Durable materials – designed to withstand high cooling system temperatures and pressures
Cost-effective solution – this bleeder screw offers original equipment quality at a competitive price
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$8.79

This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:

Upgraded material – this brass coolant air bleeder screw reduces future maintenance costs by replacing the original equipment plastic screw on specified BMW, Mini, Chrysler, Dodge, Jeep, and Ram vehicles
Ideal solution – instead of wasting time wrestling with a deformed plastic screw head, this sturdy brass screw ensures easy, reliable removal and reuse
Durable construction – made of quality brass for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience