BMW 535is Brake Parts

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

ATE is one of the world’s leading OE suppliers of brake control and brake assist systems. Hydraulic brake boosters make efficient use of the existing energy supply system in a vehicle. The hydraulic pump is used to supply, for example, power steering with the necessary high-pressure oil. It is only about the same size and weight as the tandem master cylinder. It has a substantially higher runout pressure than vacuum boosters, and is not dependent on a vacuum supply. It can therefore also be used without problem on diesel engine vehicles or on vehicles whose engines produce low vacuum levels. If the steering pump fails, the hydraulic pressure reservoir contains an adequate pressure reserve to apply the brakes several times with full boost effect. Even after this pressure reserve has been used up, it is always still possible to brake – although without reinforcement, and therefore with a significantly greater force from the foot.

Product Features:

• Original equipment (OE) quality
• Wide range of single and tandem Brake Boosters
• Unique tie-rod design meaning lighter and thinner parts for more efficient performance

Brake Reservoir Cap

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Coat-Z protective anti-corrosion coating
• No formation of rust at the hub and herewith improved visual appearance
• Immediate functional capability without removal of the coating before mounting
• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Coat-Z protective anti-corrosion coating
• No formation of rust at the hub and herewith improved visual appearance
• Immediate functional capability without removal of the coating before mounting
• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
• Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on top of brake pressure regulator. Coarse thread pitch.

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

• Triggers a warning light on the dashboard
• Should be replaced each time the brake pad is replaced
• Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

• Short closing paths
• Low volume uptake
• High efficiency
• Low throttling / after-suction resistance
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS
• Compact design – ideal for installation in small spaces
• Reduced weight – by roughly 20% compared to conventional central valve technology
• Fewer components – almost half as many as compared to conventional technologies
• Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
• Low volume uptake – minimized elastic deformations due to smaller seals
• Sealing cups supported in the housing – robustness against soiling and wear; longer life
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

• Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
• Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
• Quality assured – materials tested to exacting government-regulated safety and durability standards
• Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings
• Brand may vary by location

Bosch QuietCast Premium raises aftermarket brake pad technology to a whole new level. Employing the industry’s best pre-attached, rubber core shims and Molded Shim Technology (on selected applications), QuietCast delivers the quiet operation you and your customers expect with the durability and long life that are the hallmarks of all Bosch products. Every Bosch QuietCast Disc Brake Pad is fitted with the industry’s best pre-attached rubber core shim. This shim style is the most predominant type used by OE manufacturers and is exclusively offered by Bosch for the independent aftermarket.

Product Features:

• OE-Equivalent and Direct Fit application.
• OE style rubber-core shims
• Advanced, platform-specific Semi Metallic formulation
• Dedicated engineers source and rigorously test all friction materials and formulations
• Manufactured under the same exacting quality standards as OE components and system
• Powder-coated backing plate
• Rigorous physical and dynamometer testing
• Synthetic lubricant in box
• Pads individually wrapped Bosch Molded Shim Technology (MST)*** (On Select Applications)
• At the time of pressing, heat, adhesive and pressure mold the multi-layer shim to the backing plate and friction material creating an integrally molded unit.
• Shim stays attached throughout the life of the pad; won’t walk or slide on the backing plate
• Provides maximum stability resulting in quieter shim performance over the life of the pad

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

• Dependable stopping power
• Single layer shim for quiet braking
• OE-designed slots and chamfers to reduce noise and vibration
• Powder-coated backing plate prevents corrosion

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific friction formulations provide shorter stopping distances and extended pad life
• Hardware included for most applications, provides better value and
• OE-designed slots and chamfers to reduce noise and vibration
• Multi-layer shim provides near silent braking
• Powder-coated backing plate prevents corrosion

Nut

The AMA/URO Stop Light Switch is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium aftermarket replacement
• Provides performance and dependability
• Manufactured to meet OE specifications