BMW 533i Brake Parts

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on side of brake pressure regulator. Fine thread pitch.

ATE is one of the world’s leading OE suppliers of brake control and brake assist systems. Hydraulic brake boosters make efficient use of the existing energy supply system in a vehicle. The hydraulic pump is used to supply, for example, power steering with the necessary high-pressure oil. It is only about the same size and weight as the tandem master cylinder. It has a substantially higher runout pressure than vacuum boosters, and is not dependent on a vacuum supply. It can therefore also be used without problem on diesel engine vehicles or on vehicles whose engines produce low vacuum levels. If the steering pump fails, the hydraulic pressure reservoir contains an adequate pressure reserve to apply the brakes several times with full boost effect. Even after this pressure reserve has been used up, it is always still possible to brake – although without reinforcement, and therefore with a significantly greater force from the foot.

Product Features:

• Original equipment (OE) quality
• Wide range of single and tandem Brake Boosters
• Unique tie-rod design meaning lighter and thinner parts for more efficient performance

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

• Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
• Positive mold technology for consistent wear and performance
• Thermal scorched pad surface for a fast break-in
• Chamfered and slotted to ensure noise free braking
• Powder coated backing plate resists rust and corrosion to provide extended pad life
• Multi-Layer rubberized shims provide virtually noise-free braking
• Includes Premium hardware for easy installation

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

• Triggers a warning light on the dashboard
• Should be replaced each time the brake pad is replaced
• Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

Brake Reservoir Cap

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

The FAE Stop Light Switch is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium aftermarket replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

• Short closing paths
• Low volume uptake
• High efficiency
• Low throttling / after-suction resistance
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS
• Compact design – ideal for installation in small spaces
• Reduced weight – by roughly 20% compared to conventional central valve technology
• Fewer components – almost half as many as compared to conventional technologies
• Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
• Low volume uptake – minimized elastic deformations due to smaller seals
• Sealing cups supported in the housing – robustness against soiling and wear; longer life
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Helps deliver a quieter, more efficient braking system
• Corrosion resistant coating for long-lasting durability against harsh roads
• Manufactured with quality materials to suppress high stress levels

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

• Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
• Tensile minimum load holds up to 1800 N
• All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
• Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
• Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
• Brand may vary by location

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Prevents noise and premature wear
• Provides longer brake life and performance

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Coat-Z protective anti-corrosion coating
• No formation of rust at the hub and herewith improved visual appearance
• Immediate functional capability without removal of the coating before mounting
• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning