Audi RS4 Brake Parts

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Ensures the brake pads are meeting the rotors at the correct angle for an even braking system
• Corrosion resistant coating for long-lasting durability against harsh roads
• Manufactured with quality materials to suppress high stress levels
• Helps deliver a quieter, more efficient braking system

An axle disc hardware kit with pins (upper/lower or inner/outer) that the caliper slides on. Replace old corroded pins and bolts which can hamper caliper movement and cause unnecessary and uneven pad wear.

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

This part matches Original Equipment (OE) quality specifications which means that it is at least as good if not better than the original part the manufacturer supplied the car with. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

• Include the OE specified shims.
• Low noise and reduced vibrations.
• Formulated to OE Specifications.
• Superior friction qualities.
• Organic blended compound.

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

• OE-Equivalent and Direct fit Application
• made of special cast iron with high carbon content
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.
• Contains the same high quality craftsmanship as the original equipment manufacturer.
• Guarantees OE quality performance, durability and fitment.

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

• OE-Equivalent and Direct fit Application
• made of special cast iron with high carbon content
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.
• Contains the same high quality craftsmanship as the original equipment manufacturer.
• Guarantees OE quality performance, durability and fitment.

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Maintains proper movement for safe, effective stopping performance
• Prevents noise and premature wear

Dorman’s Brake Master Cylinder Caps are engineered for affordability and convenience. Save time, money and labor by replacing only the Cap, instead of the entire Brake Master Cylinder.

Product Features:

• Constructed of high-quality plastic for lasting durability
• Available in diverse styles, including threaded and locking
• Protects braking system by providing a tight seal against the elements
• A necessary safety item – prevents brake fluid from splashing and/or leaking

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

• Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
• Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
• Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
• Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
• Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
• Plastic reservoirs are vacuum-tested to ensure they are leak free.

TRW Automotive supplies master cylinder brake actuation systems featuring quality and performance. TRW’s master cylinder product portfolio covers a wide range of vehicles, from small cars up to truck and SUV platforms. These systems can offer lighter weight, with options such as micro master cylinders and aluminum master cylinders through to heavy-duty master cylinders designed for the durability and variable loading conditions of the light-truck market. These systems function with the help of a series of brake fluid sensors, which are located on the reservoir tank. This series includes vacuum sensors, brake light switches, and travel sensors.

Product Features:

• Low volume uptake
• High efficiency
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS

Brake Vacuum Pump

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Exact fitment and original replacement
• New Brake Hardware prevents premature wear and maximizes performance
• Helps deliver a quieter, more efficient braking system
• Manufactured with quality materials to suppress high stress levels

Wagner TQ® brake pads feature a zero-copper friction formulation and a unique Integrally Molded Insulator (IMI™) technology for quieter operation.

Product Features:

• QUIET PERFORMANCE — Semi-metallic friction material engineered in-house to allow quiet operation and high performance
• EXCEPTIONAL BRAKING POWER — Advanced friction formulations dissipate heat for superior braking performance
• ONE-PIECE DESIGN — IMI™ technology integrates friction material, backing plate and insulator into the brake pad for select applications
• HARDWARE INCLUDED — Premium stainless-steel hardware included for select applications
• COMPREHENSIVE COVERAGE — Brake pads available for all vehicle types
• ZERO COPPER FORMULATION — Features Wagner OE25™ zero-copper friction formulation

Product Features:

• Friction Formula Specifically Designed for a European Vehicle
• European Braking Performance with an Enhanced Pedal Feel
• Clean Wheels
• Ultra-Quiet: Definitive Control of Noise, Vibration and Harshness (NVH)
• Environmentally Friendly with Low Copper Content to Comply with CA and WA 2021 Restrictions
• Ultimate Upgrade for OE Semi-Metallic and Low Metallic Brake Pads
• Extremely Rotor-Friendly for Longer Rotor Life

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific formulations designed for extended pad life and clean wheels
• Multi-layer shim for near silent braking
• OE designed slots and chamfers for consistent performance
• Hardware included on popular and late-model applications

Brake Pad Set

Carquest Platinum Professional brake pads are a premium alternative to original equipment brake pads that provide superior stopping performance, quieter braking and cleaner wheels. All CQ Platinum Professional brake pads are manufactured by a vertically

Product Features:

• Industry-leading number of application specific formulations for maximum performance and extended pad life
• On-vehicle testing similar to original equipment tests
• Patented 4-Layer HEX Shim Technology provides quiet braking
• HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
• Burnishing compound allows for a faster break-in of pads and rotors
• PTFE coated hardware and caliper pin grease included for nearly every application
• Wear sensors included on most European applications that require replacement
• Powder-coated backing plate prevents corrosion

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

• Dependable stopping power
• Single layer shim for quiet braking
• OE-designed slots and chamfers to reduce noise and vibration
• Powder-coated backing plate prevents corrosion