AMC Rebel Performance and Racing Products

The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

• Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
• Electric Choke
• 4 Barrel Count
• Square Bore
• Smooth Secondary Transition
• Both Timed and Full Vacuum Ports
• Includes PCV Outlet

Product Features:

• Non-Rotator Type
• 1.550 in. Outer Diameter
• .190 Wire Size
• Single Coil Spring Type
• Set of 16

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for AMC/Jeep V8 engines, this valve cover features triple chrome-plated steel construction. Sold in pairs, this standard height cover is built to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

• Designed for AMC/Jeep V8 engines
• Sold in pairs
• Triple chrome-plated steel construction
• Stock height
• Features OEM style sealing edge

Finally an answer for your amps worn out breaker points distributor! This Ready-to-Run Pro-Billet distributor has a built-in inductive module that produces up to 7.5 A to create a high voltage spark at the plug. This spark improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance. Since this distributor has its own ignitions module there is no need to run an MSD Ignition control. Installation of the distributor is simple with only three wires to connect with the supplied Weathertight harness. Under the MSD cap is a mechanical advance that is supplied with different advance springs and stop bushings, giving you 24 curves to choose from. the ready to run AMC distributor also has a vacuum advance canister and is supplied with everything you need for installation.

Product Features:

• Simple and clean three wire installation
• CARB E.O. Approved
• Does not require an MSD Ignition Control
• Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Maintenance-free magnetic pickup and precision reluctor
• Creates stable trigger signals throughout the rpm range
• Vacuum advance canister for improved economy (can be locked out)
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• CNC machined billet aluminum housing and billet aluminum base
• Built-in module produces a 7.5 amp single spark through high rpm
• Includes built-in Rev Limiter

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Product Features:

• 0.0625 in. Thickness
• 1.80 in. x 1.30 in. Port Size
• For AMC Engines
• Gray Color
• Two Piece Configuration

The Edelbrock #7372?head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit

Product Features:

• Head: 4.275″ Bore/0.045″ Thick/10.60cc Vol.
• Intake: 1.13″x2.21″ Port/.030″ Thick
• Exhaust: 1.80″x1.30″ Port
• 3/16″ Valve Cover
• Multi Piece Configuration

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 54cc Dual-Quench Combustion Chamber
• Offers Improved Mid To High Lift Flow
• Thicker Deck Surfaces than Other Brands

Distributor Condenser

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

• Ideal For Tight Spaces
• Serrations Prevent Loosening
• Flange Distributes Pressure
• Zinc Plated Bolts
• Grade 5 Material
• Easy Installation

Product Features:

• FORD 9″ SOLID SPACER KIT

Manufactured from high-density cork/rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For original equipment replacement and high performance street.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• Provides excellent sealing and durability
• Complete with molded rubber front/rear oil pan end seals where applicable
• For OE replacement and high performance street use

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

• See catalog for application information
• Features 60K V Rated Alkyd Compound

CUP

Edelbrock part #7531 RPM Air-Gap AMC intake manifold is designed for 1970-91 304-401 c.i.d. V8 applications. The RPM Air-Gap intake manifold incorporate the same race-winning technology as our Victor Series competition intakes. The air-gap design features

Product Features:

• Based on Performer RPM-Series with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• Designed for 1500 to 6500 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Includes Std Oil Fill ; PCV ; A/C Accy Bosses
• Not for Exhaust-Heat Chokes – No Exhaust Crossover

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

• Replacement Distributor Gear

Product Features:

• Hex Head Drive Type
• 3.78 in. Length
• 0.5 in. Thread Diameter
• Coarse Thread Type
• Chromoly Material

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

• Indicates coolant temperature
• Helps prevent coolant injuries
• Fahrenheit and centigrade readings
• Color-coded temperature ranges
• Integrated coolant reclamation valve
• Improves under-hood appearance
• Chromed crown with a colored trim ring

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads