Acura Legend Belts and Hoses

Essential Acura Legend Belts and Hoses

Dayco – Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves (Part No.89038)

Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves

from

$33.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl

Product Features:
  • Designed for the majority of automotive vehicle applications on the road today
  • High-quality materials help resist wear and improve belt life
  • Features premium lubricated bearings to extend service life
  • Meets or exceeds OE quality
See More

Gates – Premium Molded Coolant Hose (Part No.21607)

Premium Molded Coolant Hose

from

$27.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Dayco, Heater Hose, 90 Trim-to-Fit (Part No.R3030752627DAY)

Dayco, Heater Hose, 90 Trim-to-Fit

from

$16.22
Dayco, Heater Hose, 90 Trim-to-Fit

Dayco – Bottom Cog V-Belt; 42.5 Inch Long, Exact Fit Premium Quality (Part No.15425)

Bottom Cog V-Belt; 42.5 Inch Long, Exact Fit Premium Quality

from

$16.79
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.

Product Features:
  •  Provides greater durability and flexibility – 35% stronger than all previous versions
  • Prevents electromechanical interference issues on modern vehicles
  •  Resists heat, oil and grease
See More

Bando – Precision Engineered V-Belt (Part No.W100046050BAN)

Precision Engineered V-Belt

from

$6.39
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.

Product Features:
  • Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
  • Precision molded teeth are protected by durable fabric facing for long life
  • Tensile cord is engineered and tested for maximum load carrying capabilities
  • Rubber backing resists abrasion, oil and heat
See More

Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25260)

Vulco-Flex½ II Flexible Coolant Hose

from

$45.99
Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

MacKay – MacKay Radiator Hose (Part No.G200058269MKY)

MacKay Radiator Hose

from

$25.51
MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:
  • Excellent resistance to high temperatures
  • Resists chemical attack (oils, fuels etc.)
  • Excellent Ozone resistance
  • Good resistance to abrasion
  • High resistance to vibration
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900044A)

O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter

from

$34.49
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:
  • Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
  • Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
  • Installation instructions included.
See More

Dayco – Dayco, Acc. Belt Idler Pulley (Part No.G60201221066DAY)

Dayco, Acc. Belt Idler Pulley

from

$21.41
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.

Product Features:
  • OE-Equivalent and a direct fit application.
  • Precision bearing
  • OE High quality pulley assembly
  • Durable long life performance.
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot) (Part No.28407)

Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot)

from

$0.99
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Dayco – Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia. (Part No.81041)

Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia.

from

$14.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
  • This hose is designed to prevent splitting, ballooning, and elongation
See More

Gates – Premium Molded Heater Hose (Part No.18020)

Premium Molded Heater Hose

from

$14.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Micro-V« Serpentine Drive Belt (Part No.K040360)

Micro-V« Serpentine Drive Belt

from

$28.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:
  • Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
  • EPDM rubber constructions resist cracking on the rib surface
  • Meets or exceeds all specifications from the Original Equipment Manufacturer
  • Tensioner Replacement is Recommended (if equipped)
  • Unique form grinding of each individual belt assures precise dimensional control.
  • Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
See More

Driveworks – Poly Rib Belt Serpentine Belt; 36.81 Long, 5 Rib Count (Part No.368K5)

Poly Rib Belt Serpentine Belt; 36.81 Long, 5 Rib Count

from

$13.49
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Dayco – Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count (Part No.5040358)

Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count

from

$24.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length (Part No.80400)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length

from

$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Gates – Premium Molded Heater Hose (Part No.18204)

Premium Molded Heater Hose

from

$20.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Molded 90 Degree Heater Hose (Part No.28467)

Molded 90 Degree Heater Hose

from

$15.29
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Heater Hose (Part No.18230)

Premium Molded Heater Hose

from

$19.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Coolant Hose (Part No.21591)

Premium Molded Coolant Hose

from

$25.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.31" Diameter (Part No.C71292)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.31" Diameter

from

$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Premium Molded Coolant Hose (Part No.21920)

Premium Molded Coolant Hose

from

$33.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.19" Diameter (Part No.E71535)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.19" Diameter

from

$20.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Helping You Find the Right Belts and Hoses for Your Acura Legend

You love your Legend. So we’ve made it easier than ever to help you find Acura Legend Belts and Hoses in our online catalog. Our inventory holds 63 aftermarket and OEM Belts and Hoses for your Acura Legend, ranging from $0.99 to $79.99.

We offer parts from 9 brands trusted to make quality Belts and Hoses for your Acura Legend. Before you buy, take some time to read through customer reviews. We currently have 2,038 reviews of Acura Legend Belts and Hoses from previous customers. Some of the top rated parts include Multi-Rib (Serpentine) Belt with 4.7 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.31" Diameter with 3.7 stars.

Find your Legend Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Acura Legend part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Belts and Hoses Brands for Your Acura Legend

Our inventory holds Belts and Hoses for your Acura Legend from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Gates, and Driveworks, all of which can keep that Acura happy.

Top-Rated Dayco Belts and Hoses

Leading Dayco Belts and Hoses

We carry Dayco brand parts for your Acura Legend across several catalog categories, including Heater Hoses and Serpentine and V Belts. Some of our most reviewed Dayco parts include:

FAQs for Acura Legend Belts and Hoses

What are the most purchased Belts and Hoses for the Acura Legend?

Out of 63 Belts and Hoses for the Acura Legend, the most popular in our inventory are:
Safety Stripe« Standard Straight Heater Hose
from $2.49
This product is not rated
Safety Stripe« Standard Straight Heater Hose
By-Pass Hoses
Poly Rib Belt Serpentine Belt; 37.55 Long, 4 Rib Count
from $19.79
This product is not rated
Poly Rib Belt Serpentine Belt; 37.55 Long, 4 Rib Count
Serpentine Belts

What are the top-rated Acura Legend Belts and Hoses?

Top-rated Belts and Hoses for your Acura Legend based on customer reviews/ratings are:
Multi-Rib (Serpentine) Belt
from $10.55
(62)
Multi-Rib (Serpentine) Belt
“Good”
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.31" Diameter
from $23.99
(6)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.31" Diameter
“Quality curved radiator hose. Perfect fit.”
Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia.
from $19.49
(5)
Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia.
“Replacing possibly damaged hose, secondary to overheating, and unknown age of the component.”