2023 Audi S4 Fluids and Chemicals

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

Extended Protection Automatic Transmission Fluid – 6 Quarts

Pentosin FFL-4 is the only approved First Fill and Service Fill transmission fluid for the new generation of BMW double clutch gear transmissions (DCT). Pentosin FFL-4 is founded on a fully synthetic base oil technology for safe operation at even the highest thermal load. FFL-4 features a special clutch friction performance which makes it mandatory to be applied solely to the double clutch gear box do not mix with any other gear oils.

Product Features:

• Formulated anti-wear chemistry and friction modifiers guarantee stable friction performance in modern transmissions.
• Fully synthetic fluid with constant stable friction characteristics under the most severe driving conditions.
• Exclusively developed for applications in the new Audi/Volkswagen, BMW, Porsche double clutch transmission.
• Features a special clutch friction performance which makes it mandatory to be applied to DCT gear box only.

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

European engines need a premium motor oil designed to help them last. Valvoline European Vehicle Full Synthetic Motor Oil. It’s the motor oil specially developed to extend the life of European-made gasoline and diesel engines. Our exclusive formula uses top wear additives, premium antioxidants and added detergents to fight wear, resist oil breakdown and defend against deposits better than industry standards. Its exceptional range of temperature protection ensures your engine will be defended when the weather and road conditions get tough. This superior level of protection makes it the best choice for most Audi, BMW, Mercedes-Benz, Porsche, and VW vehicles. Engineered with ingenuity, tested with tenacity, and proven with purpose, our formula was innovated in America with a century and a half of hands-on experience from the original motor oil brand.

Product Features:

• Advanced protection in european vehicles agains the four main causes of engine breakdown: wear friction heat and deposits
• Extra wear protection vs. industry and oem standards with advanced anti-wear additives
• Superior performance for european gasoline and diesel engines
• Exceptional high/low temperature protection defends your engine no matter the climate or driving conditions
• Meets or exceeds all requirements of api sp, acea a3/b3, a3/b4, mb 229.5, 229.3, &226.5, vw 50200/50500 & 50501, bmw ll-01 & ll-14fe+, porche a40, volvo 95200356, renault rn0700 & rn0710, psa b71 2296, and chrysler ms-12633/ ms-10725
• Superior engine sludge and varnish protection for European-made gasoline and diesel engines.

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• MaxLife Technology: The exclusive formula of Valvoline High Mileage with MaxLife Technology Engine Oil is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles.

Mobil 1 ESP 5W-30 is an advanced full synthetic oil specially formulated for passenger car diesels that have the latest diesel particulate filters (DPFs) and gasoline catalytic converters (CATs). The proprietary full synthetic motor oil is designed to help deliver outstanding performance and protection in conjunction with potential fuel economy benefits. Mobil 1 ESP has active cleaning agents that help to reduce deposits and sludge buildup for a cleaner engine. Helps to reduce oil aging with outstanding oxidation stability for extended drain interval protection. Low ash, sulfur, and phosphorous content help to reduce particulate buildup in DPFs and reduce poisoning of CATs. Excellent low temperature capabilities for quick cold-weather starting and ultra-fast protection. Mobil 1 is America’s leading synthetic motor oil brand at retail(1), recommended by car builders and experienced mechanics, and is the Official Motor Oil of NASCAR. ((1)Source: The NPD Group/ Retail Tracking Service/ Dollar Sales/ PCMO Full Synthetic/ 52 weeks ending July 1, 2023)

Product Features:

• Mobil 1 ESP 5W-30 full synthetic oil is formulated for passenger car diesels with diesel particulate filters (DPFs) and gasoline catalytic converters (CATs)
• Low ash, sulfur, and phosphorous content help to reduce particulate build up in DPFs
• Active cleaning agents that help to reduce deposits and sludge buildup for a cleaner engine
• Helps to reduce oil aging with outstanding oxidation stability for extended drain interval protection
• Excellent low temperature capabilities for quick cold-weather starting and ultra-fast protection
• Manufacturer Part Number: 127568
• Outstanding Performance and Protection: Designed to deliver exceptional performance and protection, with potential fuel economy benefits.

Mobil 1 Synthetic Gear Lubricant LS 75W-90 is a supreme, multi-purpose automotive gear lubricant that helps to provide exceptional thermal stability and resistance to high temperature oxidation, extending gear life due to minimal deposits. Helps to deliver outstanding protection against low speed/high torque wear with the capability to handle severe driving conditions while delivering smooth efficient performance. Mobil 1 Synthetic Gear Lubricant LS provides exceptional shear stability, corrosion protection, and enhanced frictional properties. Compared to conventional hypoid gear lubricants, Mobil 1 LS 75W-90 performs exceptionally over a wide range of temperatures to reduce wear at start up. Mobil 1 gear lube helps to minimize leakage and reduce contamination, while providing a good resistance to foaming to maintain film strength for reliable lubrication. Meets or exceeds the requirements of the following industry specifications: API GL-5.

Product Features:

• Mobil 1 LS synthetic automotive gear lubricant exceeds the highest level of performance requirements of modern passenger vehicles
• Helps to provide exceptional thermal stability and resistance to high temperature oxidation and extend gear life due to minimal deposits
• Delivers outstanding protection against low speed/high torque wear, handling severe driving conditions with smooth, efficient performance
• Compared to conventional hypoid gear lubricants, performs exceptionally over a wide range of temperatures to reduce wear at start up
• Provides exceptional shear stability, corrosion protection, and enhanced frictional properties

PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for EUROPEAN VEHICLES is a line of premium coolants specifically designed to match the technology and color requirements of European vehicles. Each coolant is formulated with the same corrosion inhibitor technology that protected your vehicle straight from the factory. Color cues on the packaging and a list of covered vehicles on the front label make it easy to identify the right match for your specific vehicle. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for EUROPEAN VEHICLES – PINK is an ethylene glycol-based antifreeze/coolant specifically developed for use in any European vehicle requiring a Pink silicate-free organic acid technology (OAT) formulation. It contains high-quality organic acid corrosion inhibitors and is free of borate, nitrite, nitrate, phosphate, silicate and amines chemicals. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for EUROPEAN VEHICLES – PINK meets the performance requirements of ASTM D3306 and BS 6580. With a complete flush and fill, PEAK guarantees this coolant will provide service life protection of up to 150,000 miles or 5 years.

Product Features:

• Matches each European vehicle manufacturer’s technology and color requirements
• Protects all cooling system metals from rust and corrosion
• Meets the performance requirements of ASTM D3306 and BS 6580
• Service life of up to 5 years/150,000 miles with a complete cooling system flush and fill
• Color-coding and vehicle applications listed on the front simplify selecting the right antifreeze/coolant
• Available as both concentrate and 50/50 products to do the job right
• Testing Requirements: For proper freeze and boil over protection, use a traditional refractometer or hydrometer to measure the percentage of ethylene glycol by volume.

Prestone® Platinum antifreeze+coolant is Prestone’s best universal antifreeze & coolant product. GUARANTEED to work with all vehicles; all makes, models, years & fluid colors. 15+ years, 350,000 miles of protection; the fluid is guaranteed for the life of your vehicle. This advanced product delivers Extreme Protection against both freezing temperatures (-50 Deg. F) and overheating / boiling over of the engine (+268 Deg. F). Prestone Platinum utilizes industry leading protection from engine damaging rust, corrosion, buildup & scale. While ordinary antifreeze coolant only focuses on the basic corrosion coverage, Prestone Platinum goes farther, adding our most advanced cooling sytem protection, allowing the system to run optimally, like when it was new. Internal buildup & corrosion damage can cause engine part failure or clogging, leading to expensive repairs and inconveniences. Prestone Platinum helps you avoid costly repairs and vehicles in the shop. This extended life coolant is guaranteed to work with all new engines and engine technology, while also being backwards compatible, improving protection in all older engines. Prestone Platinum antifreeze+coolant – Year Round Protection.

Product Features:

• Guaranteed to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT; G05®, G11®, G12®, G12++®, G13®, G30®, G40®, & GG40®. For all engines & engine sizes, new and older engines.
• 15+ Yr., 350,000 mile Extended life formula. The fluid is guaranteed for the life of your vehicle
• Includes our most advanced Prestone Cor-Guard® technology, unmatched cooling system parts protection that protects against engine damage; rust, corrosion, scale, build-up and clogging. Protection for 15+yrs / 350,000 miles.
• Ready to Use formula – Prediluted 56/54. Perfect for small volume top-off or complete drain and refill of the cooling system

Antifreeze Conventional Green 50/50 is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. Prime Green 50/50 can be used to top-off cooling systems in vehicles using conventional AF/C, will not harm rubber parts, and meets ASTM D3306 and D4985 standards.

Product Features:

• Low Silicate Formula.
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone All Vehicles antifreeze+coolant (concentrate) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines, while also being backwards compatible improving protection in all old

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Concentrate formula. Must mix with distilled to the desired mix ratio of EG & water. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

FRAM Extended Life AMAM 50/50 is compatible with ANY antifreeze/coolant in ANY vehicle with aluminum or other cooling system metals. The formulas have a blend of long-lasting inhibitors to guard against temperature extremes and the effects of rust, corrosion, and premature water pump failure. Top-off your cooling system with FRAM Extended Life AMAM 50/50, which is a blend of 50% antifreeze and 50% demineralized water. FRAM 50/50 meets or exceeds ASTM D3306 and D4985 for corrosion protection for cars and light duty trucks, while providing reliable freeze-up & boil-over protection.

Product Features:

• Formulated to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT.
• 5 Yr., 150,000 mile Extended life formula.
• Meets or exceeds ASTM D3306 & D4985 for corrosion protection.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone All Vehicles antifreeze+coolant (ready to use) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines while also being backwards compatible improving protection in all older engines. The patented Cor-Guard technology (the best innovation in the category in decades) instantly protects parts from corrosion, buildup, pitting, scaling, rust and other damage. These fluids are specially designed to not only manage the engine temp and protect from freezing up (like competitors), but they also potect the engine from damage. Internal damage can cause engine part failure, leading to expensive repairs and serious inconveniences. Avoid costly repairs and vehicles in the shop with Prestone All Vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Valvoline MaxLife Multi-Vehicle Automatic Transmission Fluid (ATF) is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Long life friction modifiers help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
• Suitable for 95% of traditional ATFs including Dex/Merc, Mercon LV & Mercon V

FRAM DEXRON®-VI FULL SYNTHETIC ATF represents the latest technology in full  synthetic automatic transmission fluids. This product is designed for the newest  generation of highly efficient transmissions now being installed in most vehicles, and is  DEXRON®-VI licensed by GM and meets JASO 1A performance requirements. It is a fuel  efficient choice for older models as well, such as those currently using DEXRON®-III. FRAM DEXRON®-VI FULL SYNTHETIC ATF is recommended for use in all GM  DEXRON® applications and in transmissions applications calling for Toyota WS, Nissan  Matic J and Matic S, Ford part numbers XT-10-QLV and XT-6-QSP, Honda Z-1 and DW 1, and Hyundai SP-VI. Check owner’s manual for specific recommendations.

Product Features:

• Outstanding resistance to oxidative and thermal breakdown.
• Exceptional low temperature fluidity.
• Excellent anti-wear properties.
• Excellent gear shift quality throughout service life.
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Castrol Transmax ATF/CVT Universal is a technologically advanced full-synthetic formulation designed to deliver excellent performance in most of the traditional stepped automatic transmissions and Continuously Variable Transmissions currently in use. It is also suitable for use in hybrids.

Product Features:

• Coverage of over 300 specs/95% of vehicles in operation
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation

Product Features:

• Fully Synthetic
• Advance transmission protection from standard to sever duty
• Resist thermal breakdown, oxidation, varnish and sludge

FRAM DEXRON®-VI FULL SYNTHETIC ATF represents the latest technology in full  synthetic automatic transmission fluids. This product is designed for the newest  generation of highly efficient transmissions now being installed in most vehicles, and is  DEXRON®-VI licensed by GM and meets JASO 1A performance requirements. It is a fuel  efficient choice for older models as well, such as those currently using DEXRON®-III. FRAM DEXRON®-VI FULL SYNTHETIC ATF is recommended for use in all GM  DEXRON® applications and in transmissions applications calling for Toyota WS, Nissan  Matic J and Matic S, Ford part numbers XT-10-QLV and XT-6-QSP, Honda Z-1 and DW 1, and Hyundai SP-VI. Check owner’s manual for specific recommendations.

Product Features:

• Outstanding resistance to oxidative and thermal breakdown.
• Exceptional low temperature fluidity.
• Excellent anti-wear properties.
• Excellent gear shift quality throughout service life.
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Automatic transmission fluid is a technologically advanced, low viscosity formulation specially designed to deliver performance and maximum fuel efficiency for modern automatic transmissions.

Product Features:

• Full Synthetic, low viscosity formulation
• OEM approved and licensed by Ford (MERCON® LV) and GM (DEXRON® -VI)
• Low viscosity formula for maximum fuel efficiency in modern automatic transmissions
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Industry Specifications and OEM Approvals: JASO-1A
• Licensed and approved for use in: All GM vehicles (DEXRON®-VI, All previous DEXRON®); All Ford vehicles which specify Mercon® LV

Pentosin Super DOT 4 is a brake fluid of superior quality for universal use in modern brake systems and ideal for vehicles with ABS systems. Pentosin Super DOT 4 offers safety against vapor lock; it has excellent resistance to absorbing and retaining water and provides superior corrosion resistance.

Product Features:

• Safety against vapor lock
• Provides superior corrosion resistance
• Long-term resistance to absorbing and retaining water.

Prestone® DOT 4 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 4. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 4 braking systems (ABS, disc or drum) and can mix with any DOT 4 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® MAX DOT 4 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 75,000 mile fluid life, our longest life fluid has 1.5X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 4, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 4 is safe to use in all DOT 4 braking systems, ABS, disc or drum, and can mix with any DOT 4 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 4. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 75,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 1.5X Longer than regular Prestone DOT 4

Pentosin DOT 4 LV is a special brake fluid of highest DOT 4 performance levels and extremely low viscosity at cold temperatures. It offers safety against vapor lock; it has excellent resistance to absorbing and retaining water and provides superior corrosion resistance. Pentosin DOT 4 LV Brake Fluid is ideal for all modern vehicles with ESP and ABS. DOT 4 LV can be used in all vehicles that require DOT 4 fluid. High safety margin against vapor lock. Long-term resistance to absorbing and retaining water. Superior corrosion resistance. Low viscosity fluid provides excellent flow performance at low temperature.

Product Features:

• Safety against vapor lock
• Provides superior corrosion resistance
• Highest DOT 4 performance levels and extremely low viscosity at cold temperatures.

Prestone® DOT 4 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 4. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 4 braking systems (ABS, disc or drum) and can mix with any DOT 4 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Type: ISO Class 6 Dot 4 Brake Fluid Specifications: Meets FMVSS 571.116, DOT 4/DOT 3, SAE J1703 as well as ISO 4925, Class 6 specifications. Volume: 1 Liter The optimal brake fluid for electronic brake systems Since the introduction of ESP, brake fluid must decelerate individual wheels in fractions of a second in order to stabilize the vehicle in critical situations (e. g. a skid). The development of particularly thin bodied brake fluids such as Original ATE SL.6 have been essential in ensuring the rapid response times required for ESP can be attained. The requirement for such fluids has already been incorporated into the design of the ESP system. With conventional brake fluids the system’s reaction times (in critical situations) may be several times longer than with Original ATE SL.6. In practice this may mean that the system cannot stabilize the vehicle. Advantages of Original ATE SL.6

Product Features:

• Low viscosity (thin-bodied)
• Permits fastest response by ESP
• Optimum brake fluid for electronic brake systems like ESP, ABS, TCS, etc.
• Improved handling safety owing to speedy response of ESP