2021 Dodge Durango Cooling and Climate Controls

Below you will find various in-demand Dodge Cooling and Climate Controls, components and accessories for your 2021 Durango. Advance Auto Parts has popular Durango parts like Blower Motor and Related Products, Blend Doors, Heating Parts and more. You’ll also find aftermarket and OEM Cooling and Climate Controls for other Durango model years including 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2022 and more. Select a category of 2021 Dodge Durango Cooling and Climate Controls below and start saving instantly.

Popular 2021 Dodge Durango Cooling and Climate Controls Categories

Humidity Sensors

HVAC Heater Blend Door Actuator Gear Kits

Radiators

Water Pumps

AC Compressor With Clutch

Blower Motors

Engine Coolant Thermostat Housing Caps

Radiator Caps

AC Compressor Without Clutch

Thermostats

Thermostat and Water Outlet Assemblies

Air Blend Door Actuators

Coolant Reservoirs

Coolant Temperature Sensors

Heater Cores

Coolant Reservoir Caps

Water Outlets

Engine Coolant Pipe O-Rings

Blower Motor Resistors

Thermostat and Water Outlet Gaskets

AC Discharge Lines

AC Suction Lines

Water Pump Gaskets

Expansion Valve and Orifice Tubes

AC High Pressure Side Switches

Radiator Drain Plugs

Radiator Support Tie Bars

Radiator Cap Adapters

Essential Cooling and Climate Controls for 2021 Dodge Durangos

from

$52.99

New Economy Replacement Radiator Support Upper Tie Bar, Except Diesel Models

Product Features:

Except Diesel Models, Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$154.99

New Platinum Pro Radiator

Product Features:

Made Of Plastic and Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$9.79

Crafted to meet the exact specifications set by Original Equipment Manufacturers (OEM), these products are engineered for effortless installation and removal. Constructed from premium-grade components, incorporating proper relief and vacuum valves, they ensure optimal performance even in the most demanding automotive cooling systems. Rigorously quality-tested, these components provide exceptional, out-of-the-box performance and superior durability to meet or exceed the highest standards of today’s vehicles.

Product Features:

Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$153.99

New CAPA Certified Standard Replacement Passenger Side Upper Radiator Support Brace

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$32.49

This air door actuator directly replaces the original actuator on specific vehicle years, makes, models, configurations and positions to restore proper HVAC operation. Please note that many vehicles have several different air door actuators, which are designed for specific positions and functions in the vehicle. To ensure you have what you need, carefully review the application notes for this part to verify it matches the position and function of the actuator you need to replace. In some online ordering systems, you may need to enter your vehicle information first to see the application notes for your vehicle. If you don’t know which actuator position you need to replace, consult a qualified service technician.

Product Features:

Direct replacement – made to match the fit and function of the original air door actuator on certain vehicle years, makes, models and configurations.
Position specific – vehicles often have multiple different HVAC door actuators; review this part’s application notes to verify it matches the location and function of the actuator you need to replace.
Durable construction – designed and tested to strict standards to help resist wear and electrical burnout for reliable operation and long service life
Trustworthy quality – backed by a team of experts and engineers in the United States, and more than a century of experience

from

$5.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$117.99

Carquest Premium offers a complete line of automotive heater cores covering 94% of all North American vehicle applications. Carquest Premium provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability. Carquest Premium offers certified heater cores that meet or exceed OE specifications and are all fitment checked in the actual vehicle’s HVAC heater module and are, thus, ready to be installed right out of the box for a “Drop-In Fit”. Carquest Premium heater cores are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.

Product Features:

All heater cores are designed and tested to match or exceed OE specifications for form, fit and performance with a clear focus on obtaining the highest heat transfer performance possible through use of quality materials and manufacturing processes to ensu
Carquest Premium heater cores are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.
Provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability.
Carquest Premium offers a complete line of automotive heater cores covering 94% of all North American vehicle applications.
Our advanced engineering methods coupled with our innovative manufacturing technology provides products to the aftermarket that meet or exceed form, fit, and function of OEM Parts

from

$33.49

Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$51.99

Carquest Hose Assemblies are designed to carry refrigerant in an air conditioning system. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$40.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$165.99

Carquest Evaporators are designed to remove heat from the air inside the passenger compartment of a vehicle resulting in cooler air temperatures. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

The design and manufacture of the evaporators result in uniform refrigerant distribution with optimal flow for improved performance and maximum heat transfer.
The evaporators are constructed to offer a lightweight, compact design that will fit easily within the engine compartment.
The surface treatment on each part ensures optimum water drainage to prevent mold and odors in the system.
The evaporators are 100% tested to meet or exceed original equipment specifications. Each part is helium tested to ensure no leaks.
O-Rings and gaskets necessary for installation are included.
O-Rings and gaskets necessary for installation are included.

from

$414.99

HL Mando is the leading original equipment manufacturer utilizing its state-of-art technology and various quality tests to offer customers great satisfaction and safety. HL Mando is producing a variety of A/C Compressor with the latest equipment that boasts highest quality from passenger vehicles to commercial vehicles. With the state-of-the-art electronic control technology that maximizes the safety and convenience of the driver and passenger, Mando is being recognized for its high quality and supply system by world’s best automakers. In addition, obtaining ISO/TS 16949 certification proves excellent quality and reliability of suspension parts. – We Are OE!

Product Features:

Pre-filled oil in it with the correct amount of oil
Tested for Quality, Durability, and Reliability
Brand New OE- No Core Exchange Required
Direct Original Equipment Replacement

from

$37.99

Air not flowing through the dash vents properly? Repair a worn or broken blend door actuator with this replacement HVAC blend door gear kit. Saves time and money by replacing only the worn gear while preserving the rest of the blend door assembly.

Product Features:

Direct replacement – this blend door gear replaces only the damaged original gear without requiring a new blend door assembly.
Quality construction – this blend door gear is made from quality materials for a long service life.
Saves time and money – huge savings replacing only the worn HVAC blend door gear instead of the complete blend door
Quality assured – this part has undergone testing to ensure a trouble-free installation

from

$3.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$18.29

Manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$46.87

Water Distribution P

from

$10.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$10.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$62.99

100% leak testing And hub-pull testing ensures reliable performance. O.E.-supplied NEW unitized seals ensure long-lasting, trouble-free performance. Unlike other aftermarket manufacturers, CARDONE installs the proper O.E. specified bearing design to meet the specific radial And axial load requirements of each application. This ensures longer bearing life And reliable performance. Original casting specifications are strictly followed to ensure proper fit for easy installation And proper water flow for maximum cooling.

Product Features:

100% leak testing and hub-pull testing ensures reliable performance.
O.E.-supplied NEW unitized seals ensure long-lasting, trouble-free performance.
The proper O.E. specified bearing design is installed to meet the specific radial and axial load requirements of each application. This ensures longer bearing life and reliable performance.
Thermostat seal and mounting gasket are supplied for ease of installation (where applicable).

from

$8.99

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
Brass sensor housing precision machined to meet or exceed OE thermal conductivity
OE precision matched thermistor position for correct output parameters
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$46.99

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$14.05

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

All units are 100% tested using automated equipment that activates the switch, checks for leaks & stresses the part to ensure specification compliance, even under the most demanding operating conditions.
Robust design and high grade materials meet the stringent demands of today’s service professional

from

$22.99

Engine Coolant Thermostat Housing with impoved durability and resistance. It can withstand extreme temperature changes that normally results in leak and crack.

Product Features:

Excellent quality,perfect fit
Easy installation
Optimizes engine cooling performance
Manufactured and tested at the ISO 9000 certified facilities

from

$61.99

This interior humidity sensor is engineered to match the fit, function and performance of the original sensor to help restore proper detection of humidity, windshield glass temperature, and dew point on specified vehicle years, makes and models..

Product Features:

Direct replacement – this humidity sensor is designed to match the fit, function and performance of the original interior humidity sensor on specified vehicle years, makes and models.
Restores functionality – engineered to help restore proper climate control cabin air recirculation mode when the factory interior humidity sensor has failed from electrical malfunction or impact
Durable construction – this sensor is made from quality materials for reliable service
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$192.99

The Carquest condenser is an integral component of the motor vehicle air conditioning system. This part condenses the refrigerant into a liquid to prepare it for entry into the compressor. The condenser is manufactured according to OEM design specifications to ensure a long life with quality performance. Exact design standards produce a seamless fit into the engine compartment.

Product Features:

This is a parallel flow condenser that contains small micro-channels. It is highly recommended that this condenser be replaced if a failure has occurred in the vehicle’s air conditioning system that has resulted in debris contaminating the system. This
The Carquest condenser production process includes quality driven details such as using zinc-coated tubes and electrostatic paint spray at high temperatures to provide the best corrosion resistance and durability in our condensers.
Continuous molds, laser welding machines, semi-automatic assembly stations and other advanced equipment provide quality products.
Each condenser uses only the highest quality raw materials including pure aluminum (not substandard or recycled) to provide the highest quality standards from beginning to finished product.
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak.
Our condensers are manufactured from rigid design standards to fit OEM dimensions.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.

from

$442.99

Carquest New Compressors are designed, manufactured and tested to meet or exceed strict original equipment specifications for superior quality and performance. Each new compressor is tested to provide durable life to the vehicle’s air conditioning system. All new compressor components are assembled using state of the art equipment and techniques to ensure smooth operation. Each part is equipped with a clutch and connector that matches the original equipment part and provides an exact replacement to your vehicle’s part. All compressors are supplied with the necessary gaskets and o-rings for installation.

Product Features:

Each new compressor design undergoes rigorous life cycle testing at high RPMs and pressures to ensure that they can withstand years in the harshest conditions.
New compressors are designed with utmost precision using 3D coordinate measuring machines to ensure a perfect fit.
The production process contains automated controls at every stage that alerts and halts production in case of an error, assuring that the finished product will always be flawless.
All new compressors must pass a helium leak test and pump up function test prior to packaging.
O-Rings and gaskets necessary for installation are included.

from

$35.99

New Standard Replacement A/C Expansion Valve, V6 Engine

Product Features:

V6 Engine
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$79.03

A/C Pressure Switch

Upgrade your 2021 Dodge Durango with Top-Quality Cooling and Climate Controls

When it comes to maintaining or upgrading your 2021 Dodge Durango, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Dodge or enhancing its overall performance, Cooling and Climate Controls are key to keeping your Durango functioning at its best. At Advance Auto Parts, we offer a wide selection of 58 Cooling and Climate Controls for the 2021 Dodge Durango, designed to meet your needs without breaking the bank. From Blower Motor and Related Product replacements to Blend Doors upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Cooling and Climate Controls for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Cooling and Climate Controls for your 2021 Dodge Durango at great prices. Our Cooling and Climate Controls inventory for this model ranges from just $5.49 to $499.99, with an average price of $89.15. Our 58 Cooling and Climate Controls in stock come from 11 trusted brands, so you’re sure to find the right part for your 2021 Dodge Durango without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2021 Dodge Durango, we stock popular OEM and aftermarket Cooling and Climate Controls from top names like FELPRO, Carquest Premium, Dorman, and more. FELPRO Cooling and Climate Controls start at just $5.49 and boast an impressive 5 stars average rating from customers. Carquest Premium and Dorman also bring quality to the table, with Cooling and Climate Controls available starting at $6.79, and at an average 4 stars rating. With 1,419 customer reviews and counting, our 2021 Dodge Durango Cooling and Climate Controls have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Cooling and Climate Control upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2021 Dodge Durango is always ready to roll. We’re committed to providing you with everything you need to keep your Durango in top shape, all in one place. Start shopping confidently below for your 2021 Dodge Durango!

Best-Selling Blower Motor and Related Products for 2021 Dodge Durangos

Enhance the driving experience in your Dodge with 5 quality Blower Motor and Related Product components, starting at $103.99.

show more show less

from

$115.99

Carquest Premium Blower Motors are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile A/C experience, fix it once and fix it right with Carquest Premium Blower Motors. Meets or exceeds OE design. Magnetic size and properties compare or exceed OEM. Windings meet or exceed OEM Specifications. Motor RPM equivalent to or exceeds OEM motor.

Product Features:

Meets or exceeds OE design and performance
Magnetic size and properties compare or exceed OEM
Windings meet or exceed OEM specifications
Motor RPM equivalent to or exceeds OEM motor

from

$146.05

Blower Motor

from

$139.99

Blower motor resistor burnt out? Restore proper heating and cooling functionality with this direct replacement resistor designed to match the operation and performance of the original equipment on certain vehicles.

Product Features:

Direct replacement – this blower motor resistor matches the fit, function and performance of the original motor on specific vehicles.
Restores performance – fixes a fan that’s only operating on one speed or not working at all
Thoroughly tested – examined and validated to perform safely and effectively
Trustworthy quality – backed by team of engineers and inspectors in the United States

from

$111.99

Meets or exceeds OE design and performance
Magnetic size and properties compare or exceed OEM
Windings meet or exceed OEM specifications
Motor RPM equivalent to or exceeds OEM motor

from

$103.99

Carquest premium direct replacement resistors are designed to match the operation and performance of the original equipment to restore the proper heating and cooling functionality.

Product Features:

Restores Functionality- Manufactured to original equipment specifications to restore full HVAC operation
Original equipment quality – Carquest blower motor resistors meet the high quality material standards and tolerances as the original equipment
Complete kit – Each kit includes the resistor, connector, and splice connectors to complete the job
Direct replacement – Carquest blower motor resistor kits are a direct replacement to the original equipment resistor

Top Picks for 2021 Dodge Durango Heating Parts

Upgrade Dodge Durangos with top-quality Heating Parts parts, including 2 OEM and aftermarket selections for your 2021 model.

show more show less

from

$165.99

All heater cores are designed and tested to match or exceed OE specifications for form, fit and performance with a clear focus on obtaining the highest heat transfer performance possible through use of quality materials and manufacturing processes to ensu
Carquest Premium heater cores are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.
Provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability.
Carquest Premium offers a complete line of automotive heater cores covering 94% of all North American vehicle applications.
Our advanced engineering methods coupled with our innovative manufacturing technology provides products to the aftermarket that meet or exceed form, fit, and function of OEM Parts

from

$147.99

Carquest Premium offers a complete line of automotive heaters covering 94% of all North American vehicle applications. Carquest Premium provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability. Carquest Premium offers certified heaters that meet or exceed OE specifications and are all fitment checked in the actual vehicle’s HVAC heater module and are, thus, ready to be installed right out of the box for a “Drop-In Fit”. Carquest Premium heaters are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.

Product Features:

Provides value in several ways, including increased thermal performance and resistance to corrosion using enhanced design features, such as the latest fin and tube technology and design standardization for maximum availability.
Meet or exceed OE specifications and are all fitment checked in the actual vehicle’s HVAC heater module and are, thus, ready to be installed right out of the box for a “Drop-In Fit”.
Engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.
Carquest heaters are engineered and manufactured under ISO TS16949 quality systems and are 100% leak tested.

In-Demand Air Conditioning Parts for 2021 Dodge Durangos

Select from 13 premium Air Conditioning Parts parts for your 2021 Dodge Durango, with prices ranging from $18.99 to $499.99.

show more show less

from

$94.99

New Platinum Pro A/C Condenser, With Integral Transmission Oil Cooler, Excludes 14-15 SRT-8

Product Features:

With Integral Transmission Oil Cooler, Excludes 14-15 SRT-8, Made Of Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$46.99

Advance Auto Parts is committed to providing high-quality ABS sensors. The entire manufacturing process is closely managed to deliver high quality products.

Product Features:

High grade materials that are equal to or better than OE provide durability and long service life
All ABS sensors are tested for proper fit, form, and function
Wire diameter and sheathing same or larger than OE to ensure product quality
Glass filled reinforced plastic for superior resistance to automotive fluids, dirt, salt and road debris
Includes all necessary brackets and hardware

from

$46.99

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$18.99

Carquest Expansion Valves are designed to regulate the flow of refrigerant through the air conditioning system to provide optimal cooling to the passenger compartment. Each expansion valve is manufactured to original equipment specifications to perform its function even in the harshest climates. Each part is supplied with the necessary gaskets and o-rings for installation.

Product Features:

The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
O-Rings necessary for installation are included.

from

$432.99

Pre-filled oil in it with the correct amount of oil
Tested for Quality, Durability, and Reliability
Brand New OE- No Core Exchange Required
Direct Original Equipment Replacement

from

$51.99

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$499.99

Carquest Premium A/C compressors are 100% new units that are manufactured to the highest quality to meet or exceed OE specifications.

Product Features:

Every unit is 100% function and leak tested
Tested for noise, vibration, durability, vacuum decay and pressure decay to ensure no leaks and longer life
Very low friction coating used on swash plate to improve durability
PTFE coated pistons improve performance and reduce wear
Rubber dampened clutch plate ensures smooth clutch engagement and reduces wear
Matched high-quality needle-roller bearing ensures low friction and high load capability
Limited Lifetime Warranty when following warranty requirements: Flush A/C System, replace accumulator/receiver dryer, replace orifice tube/expansion device, and filling with correct oil and refrigerant

from

$484.99

High quality OE replacement part with all components needed to complete the job.

Product Features:

Endurance tested the equivalent of 50k miles
Includes specific electrical connector to eliminate splicing
Charged with lubricant to reduce internal friction promoting enhanced system performance and longevity
For ease of installation this compressor includes a direct fit OE style connector as well as all gaskets, O-rings, or seals needed to repair your car

from

$109.16

A/C Evaporator

from

$75.99

The Carquest Premium line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

from

$54.27

A/C Expansion Valve

from

$40.99

from

$21.99

The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
O-Rings necessary for installation are included.

Most Sold 2021 Dodge Durango Engine Cooling Parts

Explore our best-selling Dodge parts for the 2021 Durango among 33 OEM and aftermarket options starting from $5.49.

show more show less

from

$29.49

We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:

Meets and/or exceeds OEM standard
Direct-fit replacement for ease of installation
Coated with corrosion and rust inhibitor
100% leak tested

from

$28.49

Manufactured with OEM quality materials and safety standards by an OE Supplier. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$6.79

Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$7.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$41.99

Carquest Premium Thermostats are manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$211.99

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

Thermal tested under real-life temperature simulations
High tensile strength aluminum for maximum crimp strength
Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles

from

$11.49

Cracked or lost the original engine coolant reservoir cap? Replace it seamlessly and effectively with this precisely engineered, direct replacement cap.

Product Features:

Direct replacement – this engine coolant reservoir cap directly replaces a cracked or lost original cap.
Application specific – made to match dimensions of reservoir cap on only certain vehicle years, makes and models
Seamless fit – reverse-engineered from the original equipment to fit perfectly
Excellent value – a quick, easy replacement that’s less expensive than going back to the dealership

from

$134.99

Carquest Premium water pumps are 100% new, high-quality parts that meet or exceed original equipment (O.E.) specifications. All components, including the housing, hub, bearings, gaskets and seals are designed for long-lasting service life. These water pumps are supplied with the gaskets or seals necessary for installation. Our Carquest Premium water pumps undergo stringent testing to ensure superior performance that we stand behind with an industry-leading warranty.

Product Features:

100% tested for reliable performance
Durable housing features precisely machined mounting surface for proper sealing and fitment
Equipped with weep chamber or similar feature to help prevent unnecessary replacement
Included heavy-duty unitized bearings, pressed-on hubs and optimal impeller clearance for a long-lasting water pump
All gaskets or seals necessary for water pump are included
This pump is driven by the accessory belt and we recommend replacement if nearing service recommendation

from

$146.99

New Platinum Pro Radiator, 3.6 Liter, 5.7 Liter, 6.4 Liter Engines, With Heavy Duty Cooling

Product Features:

3.6 Liter, 5.7 Liter, 6.4 Liter Engines, With Heavy Duty Cooling, Made Of Plastic and Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$31.99

This premium upgraded thermostat is everything you were looking for. UltraStat Thermostats are the toughest thermostats on the market. All heavy gauge stainless steel construction provides long-life durability, as well as complete corrosion resistance. Exclusive BLVT Valve technology minimizes thermal shock to cooling system components. This is the perfect upgrade to help insure your cooling system is working exactly as you need and expect it to for longevity.

Product Features:

Heavy gauge stainless steel components offer increased reliability and long-lasting durability
Exclusive BLVT Valve Technology minimizes thermal shock to cooling system components
Stainless steel thermal element for unmatched corrosion resistance and revolutionary REAX wax mixture provides quicker reaction time
AccuSpring Design for stable temperature control and increased cabin comfort

from

$25.99

This replacement engine coolant thermostat housing is engineered to match the fit and durability of the stock thermostat housing on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

Ideal replacement – this engine coolant thermostat housing directly replaces the original housing on specified vehicle years, makes and models.
Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking.
Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housings

from

$61.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$14.29

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

Machined metal construction
Works with MT-300 pressure tester
Tests coolant caps
Professional quality

from

$88.99

This replacement engine coolant reservoir is manufactured from quality materials to withstand the stresses of underhood heat and engine vibration. It is engineered and manufactured to match the fit and function of the original part.

Product Features:

Direct replacement – this engine coolant reservoir matches the fit and function of the original part.
Ideal solution – engineered for a seamless installation.
Durable construction – manufactured from quality materials to withstand underhood heat and vibration
Trustworthy design – backed by 100 years of automotive aftermarket experience

from

$7.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$5.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$226.99

New CAPA Certified Standard Replacement Passenger Side Upper Radiator Support Brace

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$217.99

New Standard Replacement Radiator Support Lower, All Models Except Diesel

Product Features:

All Models Except Diesel, Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$153.99

New CAPA Certified Standard Replacement Passenger Side Upper Radiator Support Brace

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$121.99

New CAPA Certified Standard Replacement Driver Side Upper Radiator Support Brace

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$109.99

New CAPA Certified Premium Replacement Radiator Support Upper Tie Bar, All Gas Models, Made Of High Strength Steel

Product Features:

All Gas Models, Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$99.99

New Standard Replacement Passenger Side Upper Radiator Support Brace

Product Features:

Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$65.49

Thermostat Housing

from

$62.99

This replacement engine coolant thermostat housing assembly is engineered to match the fit and durability of the stock housing assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

Ideal replacement – this engine coolant thermostat housing assembly directly replaces the original water outlet on specified vehicle years, makes and models.
Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking.
Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housing assemblies

from

$56.99

Direct replacement – this engine coolant reservoir matches the fit and function of the original part.
Ideal solution – engineered for a seamless installation
Durable construction – manufactured from quality materials to withstand underhood heat and vibration
Trustworthy design – backed by 100 years of automotive aftermarket experience

from

$52.99

New Standard Replacement Driver Side Upper Radiator Support Brace

Product Features:

Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$52.99

New Economy Replacement Radiator Support Upper Tie Bar, Except Diesel Models

Product Features:

Except Diesel Models, Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$50.99

New Economy Replacement Passenger Side Upper Radiator Support

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$27.99

Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.

Product Features:

The engine coolant temperature sensor is located anywhere within the engine cooling system and contains a thermistor that changes in resistance value as the thermistors ambient temperature changes. The engine coolant temperature sensor is a primary input
Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
Thermally conductive grease within the housing providing the most accurate temperature transfer from the engine to the thermistor.
Plated brass or aluminum housings to prevent housing corrosion, ensures effective heat distribution to thermal element, and ensure a secure and leak-free thread mount.
Computer-Aided Design (CAD), laser scanning and 3D printing “ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) “ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.

from

$9.28

Radiator Cap

from

$8.99

100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
Brass sensor housing precision machined to meet or exceed OE thermal conductivity
OE precision matched thermistor position for correct output parameters
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$6.99

This radiator drain petcock is a direct replacement for the original equipment plug that may have deteriorated or corroded. Made of quality materials, this petcock is engineered to strict standards for durable use over time.

Product Features:

Direct replacement – this radiator drain petcock matches the fit and function of the original equipment part
Durable construction – this part is made of quality materials for a long service life
Saves money – offers original equipment quality at a competitive price
Quality assured – this petcock has undergone virtual testing to assure proper fit and function

from

$5.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

Top-Rated Cooling and Climate Controls Brands For Your 2021 Dodge Durango

Shop for the best-rated brands offering Cooling and Climate Controls and other products for your 2021 Dodge Durangos. Below you’ll find some of our best rated Cooling and Climate Controls from FELPRO, Carquest Premium, and Dorman, and more. Cooling and Climate Controls from these brands that fit a 2021 Durango start at just $5.49 and are rated as high as 5 stars. OEM and aftermarket Cooling and Climate Controls don’t get more top quality, durable, and affordable than from the brands below.

Popular FELPRO 2021 Dodge Durango Cooling and Climate Controls

When it comes to maintaining or upgrading your 2021 Dodge Durango, using quality Cooling and Climate Controls is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Cooling and Climate Controls, specifically designed for the 2021 Dodge Durango. With over 4 FELPRO brand Cooling and Climate Controls in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $5.49, with an average price of just $6.64. Plus, with over 40 customer reviews and an average rating of 5 stars, you can trust that our FELPRO Cooling and Climate Controls will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$5.49

This product is not rated

Engine Water Pump Gasket

“”

from
$7.79

This product is not rated

Engine Coolant Thermostat Housing Gasket

“”

from
$5.49

This product is not rated

Engine Coolant Thermostat Housing Seal

“”

Popular Carquest Premium 2021 Dodge Durango Cooling and Climate Controls

Carquest Premium auto parts is one of the highest quality Cooling and Climate Control brands in the market. Any 2021 Dodge Durango owner should feel confident when installing genuine Carquest Premium parts in their vehicle. To ensure the best fit and performance for your 2021 Durango, Advance Auto Parts carries a full inventory of 23 Carquest Premium Cooling and Climate Controls. Plus you will be keeping your Dodge in peak condition while saving money because prices on these Carquest Premium Cooling and Climate Controls range from $6.79 to $499.99, plus, with more than 277 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Cooling and Climate Controls below will deliver on both quality and value.

from
$14.29

This product is not rated

Radiator Cap Tester Adapter

“”

from
$165.99

This product is not rated

Heater Core

“”

from
$46.99

This product is not rated

ABS Wheel Speed Sensor

“”

FAQs for 2021 Dodge Durango Cooling and Climate Controls

Which Cooling and Climate Controls are best-sellers for 2021 Dodge Durangos?

Out of 58 Cooling and Climate Controls that fit 2021 Dodge Durangos, the following parts are the top sellers:

Engine Coolant Thermostat Housing Gasket (20780134) – $7.79
Standard Thermostat:With Seal, 192 Degrees (10321764) – $41.99
Radiator (10637269) – $211.99

What’s the price range for 2021 Dodge Durango Cooling and Climate Controls?

Cooling and Climate Control prices for the 2021 Dodge Durango start at $5.49 and go up to $499.99 for the most premium parts.

What’s the average price of a Cooling and Climate Control for a 2021 Dodge Durango?

The average price for Cooling and Climate Controls for the 2021 Dodge Durango is $89.15. Keep in mind the variety of part types within our Cooling and Climate Control category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Cooling and Climate Controls for other Dodge Durango model years?

Yes, we currently carry Cooling and Climate Controls for 25 model years of Dodge Durangos between 1998 and 2024. Cooling and Climate Controls are bought most frequently for the following model years: 2022, 2020, 2019, 2018, 2017, 2016, 2015, 2014, and 2013.

What are the cheapest Cooling and Climate Controls for my 2021 Dodge Durango?

The cheapest 2021 Dodge Durango Cooling and Climate Controls we carry in stock are:

Engine Coolant Thermostat Housing Seal (19783797) – $5.49
Engine Water Pump Gasket (11902647) – $5.49
Radiator Cap: 18 PSI (17110022) – $6.79
Radiator Drain Cock Screw-In Type With Washer (50002914) – $6.99
Engine Coolant Thermostat Housing Gasket (20780134) – $7.79

What are the top-rated Cooling and Climate Controls that fit the 2021 Dodge Durango?

Out of 1,419 reviews by customers, our 2021 Dodge Durango Cooling and Climate Controls have an average customer rating of . These are some of the highest-rated Cooling and Climate Control types for the 2021 Dodge Durango and their top-rated products:

Blower Motor and Related Products
- Blower Motor: With Wheel (11000982) – $115.99
Engine Cooling Parts
- Blower Motor: With Wheel (11000982) – $115.99

What types of Cooling and Climate Controls do you sell for my 2021 Dodge Durango?

As of 2/5/25, these are some of the most in-demand types of Cooling and Climate Controls for a 2021 Dodge Durango:

Can I get help with 2021 Dodge Durango Cooling and Climate Control orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Dodge Cooling and Climate Controls and more.

What is your return policy for Dodge Durango Cooling and Climate Controls?

Advance Auto Parts keeps returns simple. For new Dodge Durango Cooling and Climate Controls and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2021 Dodge Durango Cooling and Climate Controls

KAI – Radiator Support Upper Tie Bar; Except Diesel Models; Made Of Steel (Part No.CH1225223V)

KAI – Radiator (Part No.RAD2294)

Carquest Premium – Radiator Cap: 16 PSI (Part No.10230)

KAI – Radiator Support (Part No.CH1225225C)

Dorman – HVAC Blend Door Actuator: 1 Piece (Part No.604-059)

Felpro – Engine Coolant Thermostat Housing Seal (Part No.35857)

Carquest Premium – Heater Core (Part No.910446)

Carquest Premium – Radiator Cap: 22 PSI (Part No.10382)

Carquest Premium – A/C Discharge Line Hose Assembly (Part No.T55116)

Carquest Premium – ABS Wheel Speed Sensor (Part No.ARC2723)

Carquest Premium – A/C Plate and Fin Evaporator (Part No.T44090)

MANDO – OE AC Compressor w/ Clutch & Pre-filled Oil (Part No.10A1069)

Dorman – HVAC Blend Door Gear Kit (Part No.926-133)

Felpro – Engine Coolant Outlet Gasket (Part No.35064)

Motorad – Standard Thermostat: With Thermostat Insert, With Seal, 203 Degrees (Part No.724-203)

Gates – Water Distribution P (Part No.G20271066164GAT)

Crown Auto Jeep Replacmnt – OE Replacement (Part No.4682828)

Felpro – Engine Water Pump Gasket (Part No.35760)

Driveworks Water Pumps – Water Pump – Domestic Reman (Part No.58-481)

Carquest Premium – Coolant Temperature Sensor (Part No.WTC1563)

Carquest Premium – A/C Suction Line Hose Assembly (Part No.T55774)

Carquest – HVAC Blower Motor Resistor (Part No.RU1074)

Carquest Premium – Thermostat Housing Water Outlet (Part No.902-312)

Dorman – HVAC Humidity Sensor (Part No.926-369)

Carquest Premium – A/C Condenser (Part No.3191)

Carquest Premium – A/C New, with Clutch, with 10SR17E Compressor (Part No.T158337)

KAI – A/C Expansion Valve, V6 Engine (Part No.ACX011814)

Santech – A/C Pressure Switch (Part No.R1054406459SII)

Carquest Premium – Blower Motor: With Wheel (Part No.76981)

Autopart International Inc – Blower Motor (Part No.R20311978736API)

Dorman – BMR (Part No.984-498)

Carquest Premium – Blower Motor: With Wheel (Part No.75100)

Carquest Premium – HVAC Blower Motor Resistor (Part No.RUC1441)

Dorman – HVAC Blend Door Gear Kit (Part No.926-133)

Dorman – HVAC Blend Door Actuator: 1 Piece (Part No.604-057)

Dorman – HVAC Blend Door Actuator: 1 Piece (Part No.604-059)

Dorman – HVAC Blend Door Actuator: 1 Piece (Part No.604-060)

Carquest Premium – Heater Core (Part No.910559)

Carquest Premium – HVAC Heater Core (Part No.910715)

KAI – A/C Condenser (Part No.CND3893)

Carquest Premium – ABS Wheel Speed Sensor (Part No.ARC1305)

Carquest Premium – A/C Suction Line Hose Assembly (Part No.T55774)

Carquest Premium – A/C Block Expansion Valve (Part No.T39477)

MANDO – New AC Compressor Original Equipment (Pre-filled Oil) (Part No.10A1521)

Carquest Premium – A/C Discharge Line Hose Assembly (Part No.T55116)

Carquest Premium – New Compressor (Part No.T198316)

Carquest Premium – New Compressor with Clutch, Nippondenso 10SRE20C (Part No.T198338)

TYC – A/C Evaporator (Part No.R11301431740TYC)

Carquest Premium – A/C Refrigerant Pressure Sensor (Part No.ACA1758)

Santech – A/C Expansion Valve (Part No.R1045513343SII)

Carquest Premium – ABS Wheel Speed Sensor (Part No.ARC2723)

Carquest Premium – A/C Block Expansion Valve (Part No.T39427)

Carquest Premium – Coolant Housing/Water Outlet (Part No.85341)

Carquest Premium – Engine Coolant HD Thermostat: With Seal, 203 Degrees (Part No.48792)

Carquest Premium – Radiator Cap: 18 PSI (Part No.10234)

Felpro – Engine Coolant Thermostat Housing Gasket (Part No.35840)

Carquest Premium – Standard Thermostat:With Seal, 192 Degrees (Part No.48799)

Carquest Premium – Radiator (Part No.813204)

Dorman – Help – Engine Coolant Reservoir Cap: Flip Top, Polypropylene, 1 Pack (Part No.54201)

Carquest Premium – New Water Pump (Part No.T5140)

KAI – Radiator (Part No.RAD13204)

Motorad UltraStats – Thermostat: With Seal, 203 Degrees (Part No.5416-203)

Dorman – Coolant Housing/Water Outlet: With Housing, 90 Degree Neck Angle (Part No.902-689)

Motorad – Integrated Thermostat Housing: With Sensor, With Seal, 194 Degrees (Part No.1009-194)

Carquest Premium – Radiator Cap Tester Adapter (Part No.12552)

Dorman – Non-Pressurized Coolant Reservoir: White, Plastic, Original Equipment Replacement (Part No.603-630)

Felpro – Engine Coolant Thermostat Housing Gasket (Part No.35975)

Felpro – Engine Coolant Thermostat Housing Seal (Part No.35857)

KAI – Radiator Support (Part No.CH1225246C)

KAI – Radiator Support (Part No.CH1225233)

KAI – Radiator Support (Part No.CH1225225C)

KAI – Radiator Support (Part No.CH1225224C)

KAI – Upper Radiator Support Tie Bar (Part No.CH1225223PP)

KAI – Radiator Support (Part No.CH1225246)

Gates – Thermostat Housing (Part No.G4010221087GAT)

Dorman – Thermostat Assembly: Includes Gasket and Sensor, 194 Degrees (Part No.902-3113)

Dorman – Pressurized Coolant Reservoir (Part No.603-002)

KAI – Radiator Support (Part No.CH1225224)

KAI – Radiator Support Upper Tie Bar; Except Diesel Models; Made Of Steel (Part No.CH1225223V)