from

$12.99

New Standard Replacement A/C System Valve Core And Cap Kit

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$38.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$103.99

GM Genuine Parts HVAC Heater Water Flow Control Valves are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These HVAC heater water flow control valves control the flow of engine coolant through the heater core. The heater water flow control valve is closed when maximum A/C cooling is selected. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Visual- and leak-tested for durability
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
GM regularly updates production and service part designs to integrate new materials and technologies

from

$427.85

Valeo manufactures a new A/C Compressor with clutch assembly that is the same quality fit and performance of the OE compressor it replaces.

Product Features:

OEM Quality Direct fit Application
Guarantees OE quality performance, durability and fitment.
A product 100% ‘new’ developed by Valeo
Matching quality compressor.
Equipped with a new clutch assembly.
Design that associates performance, output and reliability.

from

$242.99

An ACDelco Professional, premium aftermarket Engine Water Pump circulates coolant through your vehicle’s radiator and engine system to help maintain proper engine temperature and performance. The gaskets, seals, and O-rings packaged with this Professional, premium aftermarket water pump help guarantee that all necessary parts are available for trouble-free installation. ACDelco Professional Water Pumps are a high quality replacement for many vehicles on the road today. This premium aftermarket replacement engine water pump is manufactured to meet your expectations for fit, form, and function.

Product Features:

All Makes water pumps fit GM vehicles as well as a wide range of non-GM vehicles
Thoroughly tested for reliable, leak-free performance
Coated seals support seal longevity and durability
Heat-treated shaft assemblies provide superior strength and durability over non-treated assemblies
High-quality bearings are permanently sealed and lubricated for greater durability and long life
Come with premium, high-quality replacement components needed for trouble-free and accurate installation
Uniform wall sections and smooth coolant-flow cavities for efficient operation
Cast-iron or aluminum design, depending on vehicle application

from

$66.99

GM Genuine Parts Engine Cooling Fan Blades are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$82.99

This engine coolant pipe is designed to match the fit and function of the original pipe on specified vehicles. It is engineered to help ensure leak-free coolant transfer when an original pipe has failed from heat or corrosion..

Product Features:

Direct replacement – this engine coolant pipe is designed to match the fit and function of the original pipe on specified vehicles.
Ideal solution – engineered to help ensure leak-free coolant transfer when an original pipe has failed from heat or corrosion
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$116.99

HVAC Blower Motor Resistor Kit

from

$19.55

Air Conditioning Pressure Switch

from

$187.99

Climate controls stopped working? Seamlessly restore operation by easily swapping the malfunctioning original module with this fully tested replacement unit.

Product Features:

Direct replacement – this HVAC control module matches the appearance and function of the original unit on specific vehicles
Functionality-tested – module has been tested to ensure the same operation as the stock module
Simple installation – no advanced vehicle knowledge is required for proper installation and setup
Trustworthy quality – backed by team of engineers and inspectors in the United States

from

$320.99

Universal Fan Clutch

from

$81.99

Carquest Hose Assemblies are designed to carry refrigerant in an air conditioning system. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$120.61

ACDelco is a global leader in automotive replacement parts and related services and offers quality aftermarket products for most makes and models, including General Motors, Ford, Chrysler, Toyota and Honda. ACDelco has over 100 years of experience in the automotive industry and is a brand of GM Customer Care and After sales, a division of General Motors.

from

$97.96

ACDelco GM Original Equipment Engine Cooling Fan Blades are located between the radiator and engine and are GM-recommended replacements for your vehicle’s original components. The fan is a part of the engine cooling system, which moves air across the radiator and A/C condenser to remove heat from the engine cooling system and the AC refrigerant system. The fan may be belt-driven or operated by an electric motor. This cooling fan blade has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$8.99

GM Genuine Parts Engine Coolant Thermostat Seals are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These seals help close and prevent coolant from leaking out of your vehicle’s cooling system components. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Helps close and prevent coolant from leaking out of your vehicle’s cooling system components to maintain the proper engine temperature
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$19.29

This coolant O-ring kit contains all the necessary O-rings to replace or repair the engine coolant pipe on specified vehicles.

Product Features:

Ideal replacement – this coolant O-ring kit matches the factory O-rings to ensure a complete and reliable repair
Durable construction – made of quality materials for leak-free service
Complete solution – includes all O-rings required to repair or replace specified coolant pipe
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$16.99

Cracked or lost the original engine coolant reservoir cap? Replace it seamlessly and effectively with this precisely engineered, direct replacement cap.

Product Features:

Direct replacement – this engine coolant reservoir cap directly replaces a cracked or lost original cap
Application specific – made to match dimensions of reservoir cap on only certain vehicle years, makes and models
Seamless fit – reverse-engineered from the original equipment to fit perfectly
Excellent value – a quick, easy replacement that’s less expensive than going back to the dealership

from

$92.99

GM Genuine Parts A/C Accumulators are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These accumulators are used in A/C systems with an orifice tube metering device. The accumulator is located between the evaporator and the compressor, and serves to capture and store excess liquid refrigerant. This prevents liquid refrigerant from entering the compressor where it can damage the compressor. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Removes harmful moisture from the A/C refrigerant system
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
GM regularly updates production and service part designs to integrate new materials and technologies

from

$20.99

We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:

Meets and/or exceeds OEM standard
Includes quality gasket or O-ring to ensure proper seal (where applicable)
100% leak tested
Direct-fit replacement for ease of installation

from

$49.49

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

Our knock sensors are designed to respond to knock frequencies up to 1000 Hz accommodating shifts in engine knock frequency making it a more flexible sensor responding to correct engine knock over a broad range of vehicle conditions
Manufacturing processes include an automated data acquisition system to continuously monitor the sensor output to ensure that it responds with appropriate voltage output at the specified frequency range
All units are 100% tested using an accelerometer vibration test to ensure trouble-free operation
Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box

from

$112.99

Carquest Evaporators are designed to remove heat from the air inside the passenger compartment of a vehicle resulting in cooler air temperatures. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

The design and manufacture of the evaporators result in uniform refrigerant distribution with optimal flow for improved performance and maximum heat transfer.
The evaporators are constructed to offer a lightweight, compact design that will fit easily within the engine compartment.
The surface treatment on each part ensures optimum water drainage to prevent mold and odors in the system.
The evaporators are 100% tested to meet or exceed original equipment specifications. Each part is helium tested to ensure no leaks.
O-Rings and gaskets necessary for installation are included.

from

$87.99

Carquest Premium Blower Motors are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile A/C experience, fix it once and fix it right with Carquest Premium Blower Motors. Meets or exceeds OE design. Magnetic size and properties compare or exceed OEM. Windings meet or exceed OEM Specifications. Motor RPM equivalent to or exceeds OEM motor.

Product Features:

Meets or exceeds OE design and performance
Magnetic size and properties compare or exceed OEM
Windings meet or exceed OEM specifications
Motor RPM equivalent to or exceeds OEM motor

from

$40.49

GM Genuine Parts Multi Purpose Switches are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$18.88

An ACDelco GM Original Equipment Radiator Cap is a spring loaded cap that seals the radiator filler neck or surge tank, and is a GM-recommended replacement for your vehicle’s original component. It maintains pressure on the cooling system while the engine is operating, which raises the boiling point of the engine coolant. It also replenishes the system with coolant from the expansion tank (if equipped) when the engine cools off. This original equipment radiator cap has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors. Get the GM quality you know and trust with ACDelco GM Original Equipment Thermostats and Caps. Stay with the brand of parts your General Motors vehicle came with and get peace of mind that the fit, form, and function is up to the high standards and specifications of General Motors. ACDelco GM Original Equipment Thermostats and Caps are engineered for virtually every model of GM car, light duty truck, and sport utility vehicle.

Product Features:

Seal and maintain pressure on the cooling system for vehicle safety
Raise the boiling point of the engine coolant to maintain efficiency
Fit most models of GM vehicles for expanded coverage
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$67.99

This air door actuator directly replaces the original actuator on specific vehicle years, makes, models, configurations and positions to restore proper HVAC operation. Please note that many vehicles have several different air door actuators, which are designed for specific positions and functions in the vehicle. To ensure you have what you need, carefully review the application notes for this part to verify it matches the position and function of the actuator you need to replace. In some online ordering systems, you may need to enter your vehicle information first to see the application notes for your vehicle. If you don’t know which actuator position you need to replace, consult a qualified service technician.

Product Features:

Direct replacement – made to match the fit and function of the original air door actuator on certain vehicle years, makes, models and configurations
Position specific – vehicles often have multiple different HVAC door actuators; review this part’s application notes to verify it matches the location and function of the actuator you need to replace
Durable construction – designed and tested to strict standards to help resist wear and electrical burnout for reliable operation and long service life
Trustworthy quality – backed by a team of experts and engineers in the United States, and more than a century of experience

from

$690.85

An ACDelco GM Original Equipment Radiator is a heat exchanger located typically in the front of the vehicle, where air can flow through the fins while the vehicle is moving. A modern radiator is made from aluminum and plastic, while older vehicles used copper and brass. These radiators are corrosion resistant with optimal heat transfer characteristics. These original equipment radiators are engineered to fit your specific GM vehicle and will provide the same performance, durability, and service life of your factory original equipment radiator. The radiator is the heart of a vehicle’s cooling system, so get the GM quality you know and trust with ACDelco GM Original Equipment Radiators and Radiator Parts. Stay with the parts brand your vehicle came with and get peace of mind that the fit, form, and function is up to the high standards and specifications of General Motors. ACDelco GM Original Equipment Radiators and Radiator Parts are engineered for virtually every make and model of GM car, light duty truck, and sport utility vehicle.

Product Features:

Superior fin waves provide a higher heat transfer
Lightweight; the radiators have a positive heat transfer to weight ratio
Corrosion-resistant aluminum core makes ACDelco GM OE Radiators long lasting
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function